Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
I would like my device to advertise for 10s and then begin advertising again only on an external interrupt.
What steps are required to restart advertising without restarting...
I am trying to reprogram a usb dongle device from AdaFruit (Bluefruit LE Sniffer), which uses the nrF51822 SoC, using nrFGo Studio. In the device manager I'm innRF5x Bootloader...
Hello everyone
i am trying to set the password for connection whenever its start advertsing but the static passkey option will set the pssword only for bonding not for...
Hi.
I am using nRF24, nRF51, and nRF52 chips.
Today I saw nRF31562A on some device(wireless mouse of Logitech)
However I can't find any information about this chip,
even...
Hello,
I would appreciate if you could help me solve what i am trying to do. I have nrf51DK board with nrf51422 on it, PCA10028, S130 and i want to use to scan for another...
Hello,
I am working on SDK 9.0 and softdevice 8.0 and the requirement for my application is the device has to advertise till it gets connected and even after disconnection...
Dear all,
I get a new nRF51-DK and I am trying to download an hex file into it.
I downloaded and installed nRFgo studio.
I connected my nRF51-DK to my...
Hi. I've gone through a lot of documentation and can't seem to find if this is documented by Nordic semi.. please answer if you know, or can point me to experiments/documentations...
I soldered 5 pieces of PCBA with nRF51822, but I got only one PCBA which can connect to J-LINK. I checked the bad four and found that SWDIO of nRF51822 on the four board is...
I'm having a weird hardfault and, I can't make sense of it.
Here's what I do know:
nrf sdk 9.0.0;
nrf51422 on a dk;
I have RTC1, SPI0, and TWI1 enabled (also a uart for...
Hello,
call of app_pwm_init() function forces logic 1 on PWM enabled pin after advertising timeout expires. Why? It causes my LED to turn completely on after advertising...
Hello,
In my code I would like to switch between BLE advertising and listening nearby devices (and save their RSSI) in the same code. After each advertising period, I would...
i have use nrf51822 and android app(nRFuart)
i was masure currunt through DSO but i think its not accurate...
i can't masure exect(high accurate) currunt consumption in...
I read through the following post and still couldn't get debug info out.
I have tried the settings there and from another post with no luck. I'm using putty on a win 8...
