Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hi,
I have a problem is that I use the 51822 as a reader to read the 24l01's radio data.Now,I use the UART to read the instruction from the PC. If the instruction is "ON...
Hi,
I use the nrf51822 to read the data from the tag which designed by the 24l01p radio module.In the whole progress, first of all, the reading module read the instructions...
I have interfaced nRF 8001 with Arduino through MISo,MOSI,SCK etc pins and it is connected successfully. When i connected my arduino with pc, i thought nRF 8001 will start...
I'm trying to make a simple BLE app based on LED button demo (BLE_LBS.C) that probably don't use much resources. I added FIFO UART communication routines and when I tried...
I have an NRF 8001 BLE chip, can you provide the break out board schematic to make this chip discoverable to my iPhone 5 as soon as i power that break out board. And how to...
Can anyone tell me how to connect NRF 8001 with Arduino mega 2560. I have developed an iPhone application and just want to connect with NRF 8001.Please tell me how to connect...
OK, probably a dumb question:
The nRF51822 reference manual indicates that the RTC is driven by an external 32 KHz input. Can anyone confirm whether it will or will not?...
Hi
can you please help me convert these Keil pre processor calls to something that gcc compiler can . If possible i would like more information about these calls and the...
I'm using Nordic NRF51822 and the Segger JLink with the s110 Bluetooth stack active (correction: flashed on the chip, see below). When my code hard faults (say due to a dereferencing...
hi, I currently stuck in the follow section:
static void gpiote_event_handler(uint32_t pins_low_to_high, uint32_t pins_high_to_low)
{
if (pins_high_to_low & (1 << BUTTON_0...
Anyone to tell me where can i get the CDB file for nRF24LE01? I've downloaded the SDK and the nRF go Studio, but i still cannot find the CDB file.. Please help me to find...
Hello,
I'm trying to start softdevice on a custom board with nRF51822 chip and S110 device. The code hangs in SOFTDEVICE_HANDLER_INIT. It seems that EVENTS_LFCLKSTARTED...
Hello,
firstly I would like to say that I tried searching the forum for a post that has similar problems to my own. But I haven't (please tell me if i'm wrong) seen any...
Question: Can a nrf51822 acting as a server/slave message a client/master (iPad), that it has bonded with previously, to let it know that new data is available without having...
