Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Hello,
I received BLE_ERROR_GATTS_SYS_ATTR_MISSING event during connection procedure. Tried to look inside and found
/**@brief Event structure for @ref BLE_GATTS_EVT_SYS_ATTR_MISSING...
In code:
case PM_EVT_BONDED_PEER_CONNECTED:
NRF_LOG_DEBUG("Connected to previously bonded device\r\n");
err_code = pm_peer_rank_highest(p_evt->peer_id);
i get...
Hello there,
We're getting an assert in the above code in Soft Device s110 sdk 8.0.3. Can you give us some info as to what that is and how we can address it? To give you...
(EN)
I'm afraid I might no be competent enough, so I look forward to your kind help.
I'm quite new to using nRF52832 WLCSP package(raytac MDBT42 blank module) on a custom...
Hello again,
fortunately I made some progress using the IoT-SDK v0.8.0 on nRF51. I extended the MQTT-example to my needs, but there are still some questions.
The final...
Hi,We plan to establish a star network where more than 20 devices could communicate with 1 host mutually and no-interaction between devices with nrf51822 we are using now...
I have no clear concept about all those concepts, is there any tour or example clearly explain all of these?
At last my goal is that, I want to make my mobile phone app...
I have started creating a GATT using the libraries and Softdevice API provided.
All of our UUIDs are proprietary 128 bit UUIDs for both services and characteristics.
Here...
Hey everyone. I'm trying to read ADC value from sensor and send it via ble.
I use timer to get the value from sensor every 5 seconds, however ADC interruption correlates...
I would like to set the the fstorage memory location manually through fs_init() within SDK 12.1, but I am not sure how to do this. There's comments that is can be done manually...
Hello,
I am using nrf52 and sdk 12. I compiled the code bootloader_secure from the examples in sdk.
Now I want to change the 16 bit uuid to 128 bit uuid in the code. The...
nRF51822CEAA
I am using a custom PCB, this is not a Dev Kit from Nordic
Mac OS X
Eclipse Version: Neon Release (4.6.0)
Eclipse Debug Configuration:
Specified arm-none...
I am using SDK_11 s130 on nRF51-dk. I ported the peer manager from ble_app_gls to ble_app_uart and enabled pairing without bonding.
Inside ble_nus.c, I modified rx_char_add...
