Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command: west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hello, it is to my understanding that profile & service do not have fixed forms. Services make up profiles and you can choose how many and what services make up a profile...
I I'm running the ble_app_blinky example under pca10028 on the nrf dongle pca10031 using sdk11. The dongle disconnects after 24 seconds. Can anyone point to me what is the...
A typical classic or BLE get paired with the phone/central, and normally the central can decide to forget/unpair it. In this case, the device (nordic chipset) which previously...
I had created application with enabling the UART service(as in Ble_uart_app example) and tried to update the Rx characteristics of UART service in connectable mode through...
I'm sending a write authorization reply using sd_ble_gatts_rw_authorize_reply() in response to a standard Write Request with one byte of data. When I set the gatt_status to...
I am currently dealing with a strange problem when trying to use DFU OTA. When I enter DFU mode on Master Control Panel and try and update I get the following two error messages...
Does anyone have a working copy of ble_cps.c\h
The BDS (version 1.0.2095.0) plugin (v.1.2.4) does not generate code that compiles under IAR EWB
IAR ANSI C/C++ Compiler...
Hi there, I'm definitely a newb when it comes to wireless communication and communication protocols so I'd like this question to be answered at a higher level than what I...
Hello,
I am implementing a central which is scanning for advertising packets using s130, SDK11, nRF51822 and based on example ble_app_hrs_rscs_relay.
I get the advertising...
Hi,
I'm trying to porte my code from micro_esb to nrf_esb. My need is to know when a frame with correct address is received. This frame don't need to be valid just received...
Is there any way to use more than 4 buttons using app_button or BSP library?
It seems that GPIOTE can handle only 4 pin. Am I right??
uint32_t err_code;
// Button configuration...
Hi,
I am wondering if it is possible to change the RADIO data rate using SoftDevice.
I am developing an application which do not need an high data transfer but it would...
Hi,
Migration to nRF5_SDK_12.0.0_12f24da has broken build of some our projects at link stage (region RAM overflowed with stack).
During investigation I found that nfc_t2t_lib_gcc...
I'm running app_error_handler with
SEGGER_RTT_printf(0,"\nerr_code %d on line %d file %d",error_code,line_num, p_file_name);
to print out what went wrong and where...
We are writing an Android app for our own peripheral (nRF51-based). We know the handles for all the characteristics.
On Android gatt.discoverServices() needs to be called...