HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Dear support team,
I have some trouble with a custom board using the NRF51822.
Sometimes the MCU resets supuriously.
After reset I try to find out the reason by reading...
I am following the Makefile provided by Nordic, but using --reset with --program seems to fail:
>nrfjprog --reset --program _build/nrf51422_xxac_s110.hex
ERROR: Two arguments...
Hi,
i am using three s210 master devices to broadcast ANT messages to a s310 central device. The central connnects to a PC through USB dongle and BLE.
When broadcasting...
Hi,
I found several posts on this forum closely related to my problem, but non of this answer my needs. I try to program nRF51822AA with blinky example via Keil uVision...
Hi, in evothing and mbed all the UUID are 128bits long
however, in EK, the code use 16bit UUID
ex. nus.c the uuid is 0x0001 0x0002 0x0003
any one knows how to provide...
Hi,
I have just received my smart beacon kit (nRF51822 based), I have wired up my JLink programmer according to devzone.nordicsemi.com/.../
However I am having trouble...
Hi!
I'm building a mesh using beacons. Everything works good untill now, except beacons sometime stop advertising on its own. Beacon still works because he still connects...
Hi. We are going to mass production now and the lab that will certify our product says we need to have a special mode in the firmware that would do : modulated middle channel...
I want to make a custom board using nRF51822. Currently I am using nRF go studio starter kit and pca10005 board. I am using segger jtag programmer for loading code to the...
Hello,
I have a custom program based on the uart example. I can write to the device, but sending to the master fails.
I call the SendString code, but p_nus->is_notification_enabled...
Problem
I got some problem in change device name.
I found that the function of ble.gap.setDeviceName(deviceName) is useless.
So I've searching for another function...
Hi,
Does anyone know if there are plans to support RTX in the nRF52 SDK? It is included in the nRF51 SDK under external/rtx , and there is an example in examples/peripheral...
Hi,
I have purchased the nRF8001 DK and it came with no documentations. I downloaded the nRF8001 DK User Guide V1.1.
In this documentation, under section 1.3 there is...
I have setup environment on QT creator and i am using JLink GDB server debugger.The nordic chip is nrf51822 QF AA H0 and SDK is nrf51822 s110 version 8.1.0 .I read some posts...
