Hi,
I want to add scheduler server to the mesh/light sample with nrf52DK, I change the element define like below:
static struct bt_mesh_elem elements [] = {
BT_MESH_ELEM...
Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hiii,
I am working on the ble_central_and_peripheral program(s130) in sdk8.1.0 .I could connect the device to the MCP and on clicking enable service we gets the notification...
Greetings,
I find it much an arduous task trying to sift through all the SDKs and Documentations in order to find the one specific material that I need. I've installed...
when I use softDevice S110, there exists ble_evt_dispatch function, Can I define event ? if I can, how to define event and how to use event handler . Thank you !
Hi
I want to update the connection parameter and send this request from nrf51822 to a smartphone app. I see there is a function ble_conn_params_change_conn_params() for...
I'm sure there is something obvious that I am missing, but bear with me. The following link references a function called: nrf_drv_gpiote_out_config :
infocenter.nordicsemi...
I'm trying the example in the SDK v0.9.1: examples\spi_master
When I load the project, build it, and debug it, all that happens is that it goes into a failed state where...
I occasionally get an NRF_ERROR_NO_MEM error when trying to add a custom characteristic. I'm only using 3860 bytes of ZI data, stack = 2048, heap = 2048 so it seems like I...
Hi
I am working on the ble_central_and_peripheral example in nRF51_SDK_8.1.0_b6ed55f .In this example it is possible for us to connect to 3 peripherals only.But we would...
Hi, are there any examples in C for how to directly access the registers on the chip? I realize this is a super basic question, but all the register access in the examples...
Hi,guys
I set BLE parameters like this:
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(500, UNIT_1_25_MS)
#define MAX_CONN_INTERVAL MSEC_TO_UNITS(1000, UNIT_1_25_MS)
#define...
Hi,
I'm using sd_ble_gap_connect to connect to a set of known address and whitelisted devices. My central periodically (once an hour) needs to check on a known set of devices...
Hello,
I'm looking for electrical parameters in nRF52832_OPS_v0.6.pdf but I didn't find typical impedance values for analog inputs .
Also not found any value for RESP and...
Suppose I defined services (According to nAN36 Document)
#define BASE_UUID {}
#define SERVICE1 1602 // This service send a alert message Id i.e. similar to proximity hex...