Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hi,
I am trying to use the sdk version 9 for the NRF51 to take ADC samples and trasmit it over BLE over UART found in the link: github.com/.../nRF51-SDK-9-0-0
I downloaded...
For example,
CFLAGS += -DCONFIG_GPIO_AS_PINRESET
CFLAGS += -DNRF52_PAN_12
CFLAGS += -DBLE_STACK_SUPPORT_REQD
Where are -DCONFIG_GPIO_AS_PINRESET, -DNRF52_PAN_12...
Hi,
I faced a strange kind of issue while i was burning the same code on nrf51442 and nrf51882 chip. The code is running fine on the nrf51442 chip but the code wasn't running...
My µvision crashed during programming and will no longer respond to trying to program it. It boots into the bootloader mode. My computer sees it but the precompiled binaries...
Hi ,
I am using nRF51 SDK with S130 soft device lib, and it is running well when downloading the example of ble_app_uart. But when I want to modify the service UUID from...
Hi,
I'd like to check the battery level in my BLE device, and I can set a timer to handle the checking, however this means that Timer 1 would need to powered up, and hence...
Hi,
The situation: nRF51 has established a connection with the iOS/Android (custom made)App. The nRF51 goes out of the Bluetooth range. Eventually, the Bluetooth connection...
I have looked around but have been unable to find doc explaining this. If there's something around, I'd truly appreciate a pointer.
I have an existing (solar powered) device...
Hello,
i'm searching for informations about calibrating the SAADC of the nRF52. And i have read here: Link
For nRF52, there are no calibration
values that I know of...
Hi Sir/Madam
I wrote a small program for low current verification on nrf51822 development kit with starter mother board.
The program is based on "blinky_example" project...
Hello to all,I have developed a board using the NRF51822;
Currently I am using SDK v11, S130 v2.
I have a problem in my bootloader, since bootloader_app_is_valid (from...
Hi, i want to jump from my app to the bootloader, i used the function
void bootloader_app_start(void)
{
vMBt_eStopAdv_Exe() ;// Stoping the BLE ADV
sd_power_gpregret_clr...
I have a question about when the application is erased during serial DFU single-bank update:
According to the S110 Serial HCI documentation , the serial update packets...
Hi,
I just purchased an nRF51 sniffer. I have set everything up as per the UM. When I invoke the sniffer application, it says scanning for devices, but nothing shows up....
