Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
This is what we get from JLinkExe:
Found SWD-DP with ID 0x2BA01477
Could not power-up debug power domain.
Can not connect to target.
This all happens when we use P19...
Hi, i use softdevice 9.0 and s110 8.0.
I want to make 38kHz pulse.
so i tried to use nrf_drv_timer and gpio.
if i try to make 200us, it worked not bad.
but when...
Hi, everyone.
I have read the nRF5 SDK --> GPIOTE part in the infocenter. However, I have not get anything useful.
I just want to recieve a interrupt from an external...
Hi all,
I have installed the 1.21.1.3 nrfgo stdio from nordic site.
in device manger nordic board is not detecting( both nrf51 and nrf52) only in my lap.
any setting...
Hi
I am working on customization of proximity device with nrf51822 and I need to lock it to first connected device (so after first pairing I have to make blocking connections...
I took the reference of your example and instructions hear -
devzone.nordicsemi.com/.../
The program runs but get struck at sending the I2c write command .
Do I need...
Hi,
just want to make sure: is it possible to merge UICR values into hex so that I can load some values there during production in a single flashing stage?
thanks
best...
I now have my app.hex and bootloader is running at nRF51822 and yet, the nRF Toolbox finds "DfuTarg" as expected. However, after selecting my file the UI surprisingly starts...
Hi.
I'm using nRF51822, SDK10.0.0, S130.
I made "radio test" program as below at the first.
void radio_tx_carrier_test(unsigned char freq_ch)
{
NRF_RNG->TASKS_START...
Hi,
Can we add device address with all fields set to zero's to whitelist.
I went through the spec, but it doesn't talk about the address set to zeros.
Thanks,
r...
Is it possible to change data send in scan responses after each Advertising Event? I know that sd_ble_gap_adv_data_set() has constant input arguments, but it seems weird for...
Hi everyone;
Im trying to use my nrf51822 as iBeacon with "ble_app_beacon" in SDK. As you know for estimating Distance, you should calibrate it. for calibration, place...
Hi,
I have IOS application which works fine with bluetooth different than NRF. I use direct connection by UUID in IOS app. When the application is in foreground everything...
