i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I tried to modify the twi_master_using_app_twi to work with adafruit ADS1015 as a slave. I ran into this problem. It seems that the init_transfer doesn't finish so the app_twi_perform...
What development kit should I buy? Is this the right one?
www.mouser.hk/.../
What software IDE to use?
Does Keil offer free version for limited code size? What...
trying to build a simple example in sdk 11 just to run it on the nrf52-dk
of course it is missing pieces, else life would be no fun, apparently...
oh, i don't know,...
Sorry for asking as not familiar with BT terminology and un-sure which fold means what, grateful pointer to example (in SDK or similar) that can run on the dev kit. That is...
What is "1 Mbps Bluetooth low energy mode" for nRF52832?
How was the spec. changed from my old year 2013 understanding that BLE is low speed for sensor, sending tens of...
I can read temp value by pulling flag but I Want to do that by interrupt
I added this code to my Keil but interrupt on temp didn't work.
I use Adc interrupt like this definition...
Hi,
We are using NRF51 and STM32F0 on our custom board and one of our customer's requirement is the ability to program both of these MCUs in the factory. They would like...
I am using the mbed compiler.
When I produce code using the "App with Bootloader" option, I can do FOTA updates and my code runs fine, as long as I don't enable the ble uart...
Hello together,
we are running the DTM in different modes to check the module (nrf52832, sdk 5 version 11). The carrier test gives us a current consumption that meets the...
Hi
I try to program Insight ISP 130301 with a hex file, which works on nrf51 PCA10028. Unfortunately, it doesn't work. I try to loop for each pins and set it's state, and...
I'm trying cominicar me through Termite between the application plate (nRF51-Dk kit) and a device that supports BLE, but the connection between PC and the kit application...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Hi again, I posted earlier in another post that my writeCharacteristic is responding with status 6.
Details:
Android version: 5.1
Nordic device: nRf51822 S110
I have...
Hi
I want to use nrf52 LATCH register.
I can see the correct bit set in the register, but I am unable to clear this bit.
I have tried NRF_P0->LATCH =0xFFFFFFFF; for my...
