Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF52832 and SoftDevice s132.
If the application code disables the SoftDevice, then the application CAN erase UICR memory in the nRF52832 device.
The question...
I control a module over UART using app_uart_fifo. This module is controlled from nRF host by commands to perform things. This generally works fine but however, sometimes when...
Hi,
I write a code for the max6657 temperture via modifying the SPI MASTER Example. The function for reading max6675 via SPI is shown as follow
uint16_t readCelsius(void...
Dear Nordic Team,
Thanks for supporting.
How to calculate the battery voltage level from Eddystone TLM. Its always transmit 240mV.
I am using CR2302 3V battery.
...
Hi all !
Can you tell me if it is possible to flash a single nrf51822 ship directly or if it requires at least the minimum oscillator X1 in order to be flashed?
The...
Hello. I want only 1 to 1 bluetooth matching about nrf51822.
I want only 1EA central with 1EA peripheral matching.
I set as below.
1EA - Bluetooth Central - UUID...
Yesterday, I asked a question (so far, no one has answered) about how an OS upgrade on my desktop computer might have broken my ability to flash and run BLE apps on the nRF52...
Hi there,
I have two nRF52 Preview DK boards, SDK 0.9.1 and 0.9.2, and SoftDevice S132 1.0.0-3 alpha. Several months back I got the Bluetooth heart rate demo from SDK 0...
Hi,
i am trying to wake up the nrf52832 from system off with a gpio interrupt.
When the signal on my gpio pin 28 goes from Hi to Lo, i trigger a callback function in...
Hello all,
I'm building a project on the nRF52382 with the S132 (v2.0.0-4.alpha). The project includes a Central device (GATT Clients) that read and write to 2 peripheral...
Are there any specs available regarding the performance of the nRF52 ADC's internal voltage reference? Accuracy (%) and temperature drift (ppm/degC) would be good. I couldn...
Hello,
I'm developing proprietary radio protocol using nRF52 (not using softdevice) and would like to know if it is allowed to write NRF_RADIO->FREQUENCY register while...
Hello, I've got a problem with an app_timer
starting from the BLE_UART example, I've set
#define APP_TIMER_PRESCALER 4
#define CLOCK_CONFIG_LF_SRC NRF_CLOCK_LF_SRC_Xtal...
