Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hi all
Recently, I have been developing a BT module using nRF52810. However, the module couldn't communicate normally with STM32 via UART as the MCU keep rebooting. And...
I am using the BMD-350 in a new device that reads off of a sensor and changes the alert level in the IAS based on the value. Implementing the client on this peripheral, I...
Hi
I'm trying to use the nRF52840 DK debug out to program/flash an external nRF52840 IC that runs at 1.8V logic level. According to the manual, the DK is running at 3V...
When running our hardware using the J-Link debug in connector on the dev kit, BT is fully functional. But when we try to run using the very same power source (ie, the dev...
Hi all,
I'm developing a custom board that is equipped with a nRF24L01+ (directly soldered on my PCB, no breakout). The board is equipped with a PIC32, that controls also...
SDK 15.2
port_cmsis_systick.c
nrf_drv_clock_lfclk_request is part of the legacy drivers that will eventually be removed?
Does this mean for FreeRTOS I need to keep...
Hello,
I want to set the nrf24le1 module into register retention mode with timers ON but clock source from XOSC32K. I need this power saving code in my project. Also can...
Hi,
I am using adafruit Bluefruit BLE SNIFFER. My question is whether it is required to use jLink along with it to connect to it via USB. Also, I have a question can I sniff...
sdk5 15.2's app_timer.h at line 61 says:
* @details Use the USE_SCHEDULER parameter of the APP_TIMER_INIT() macro to select if the * @ref app_scheduler should be used or...
I am trying to read hts221 and ccs811 sensors from thingy and want to make the data available on UART(P0.02,P0.03).
I have tested the uart code and able to print data -...
Hi all,
I am trying to configure the LPCOMP module of the nrf52832 using registers directly, that is, without using the already generic functions that come with the sde...
Hello
I have two similar (as their producer says) boards. Both nRF52832. The main difference is in modems used for external data transmission.
SDK 15.0.0
SD 132
I...
I have an application using mesh SDK 2.1.1 that is working. I am migrating to V2.2.0. In my current code I use nrf_mesh_opt_set() to enable and disable a relay feature. I...
Hi,
Can nRF Sniffer v2.x software flashed in nRF52832 used along with wireshark sniff all BT 4.0,4.1,4.2,5.0 packets?
Please confirm so that we can proceed to buy the...
Hi there,
The DFU Nordic samples have a 4K "MBR Params" page, located in the last 4K of flash. e.g., the linker file has:
MBR_PARAMS_PAGE (rw) : ORIGIN = 0x0007E000...
