Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hello everyone, I'm trying to run my nrf51 with ADS1298 using SPI. nrf51 is master and ADS1298 is slave.
I configured SPI as
const nrf_drv_spi_config_t spi_config =...
Hi,
I'm trying to implement GPIOs in Mesh 2.0 light switch example and I'm using SDK 15.0. I'm getting undefined reference errors and I know that I have to add legacy GPIOTE...
Hello guys.
I'm new with nodic nRF52 SDK and I tried to enable debug by setting 1 on "NRF_LOG_ENABLED" in sdk_config.h, but nothing happens in com port criated by Jtag...
Custom app running on a nRF52 devboard. Serial port runs when I use the debugger and continues after I exit the debugger, but does not run from a cold start.
using the...
Hi,
In nRF5 SDK v12.3, the members of nrf_ecb_hal_data_block_t are pointers to non-const data. I was wondering if these indeed need to be non-const for the Softdevice S132...
Hi,
I have a central and peripheral device both are based on nRF52. Central device is running on SDK 12.2.0 and peripheral with SDK 11.0.0. I would like encrypt the communication...
Hello!
We're using SDK 12.3 on our application, and we're aware that the SDK is targeted to be event driven, meaning that our code should be the one keeping track of the...
I am using SDK15 , nRF52832 custom board , keil uVISION 5 , ble_app_beacon example.
I am adding timer to the example.
In below code, when I comment out update_vbatt()...
Good afternoon,
I am facing the following issue:
a client application writes to several characteristics (write with no response) I set in my chip, which trigger the execution...
Hello,
We are porting legacy application to the nrf52840. We are using Keil uVision 5.
The legacy code is using some gcc ideas and extensions so we are forced to use...
Hi ， All
I am using nrf52832 SDK12.3.
When the host runs to the discovery service but has not yet discovered the service，the slave power off. The host can no longer connect...
Hi there.
I Tested Example (secure_dfu_ble_s132_pca10040). Fine work.
but I could not find the example code to transfer the firmware.
I need the code to receive...
Hello,
I'm a little bit confused about max datalength that can be read/written in a characteristic.
See attached, a MTU of 64 bytes is negotiated thus 61 bytes available...
hello there! I am working on a project in which two devices(one is central and other is peripheral ) uses Nordic bluetooth controller nRF51822 for connection and data exchange...
