Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Dear Sr.,
Can't detect carrier
They are two PCB one TX Carrier and other mush Detect the carrier ---------------------------------------------------------------------...
mains.c
Hello Everyone,
I have deveLoped the Custom PCB whixh has the push button which is connected to VCC so i would like verify my software logic for button configuration...
Hi,
We have a new product based on the NRF52840. We are trying to add NFC record text to the firmware that based on SDK15. We could get the NFC record text from the NRF52840...
We're evaluating the nrf52840 and I am looking at the SPIM peripheral. The datasheet states the following:
"If several AHB bus masters try to access the same AHB slave at...
i am working on the Cycling Speed and Cadence sensor central configuration using nRF52832 DK in Segger Embedded Studio. I used the RSCS central example of nrf_sdk_v15.0 and...
I'm trying to migrate a working application from SDK 14.0.0 to SDK 14.2.0. I was using app_twi on SDK 14.0.0 and am now using nrf_twi_mngr on SDK 14.2.0. One difference is...
Hi all,
Just noticed the RTT logs are broken with GCC in SDK14.2 while they work fine in SDK14.1
I found the cause is the definition of the macros:
/*
* For GCC...
Hello.
I am working with a custom board. I have been wondering how to change the default polarity for a pin? I need LED_1 to have a polarity and the other 3 LEDs to have...
Hello,
I base on migration guide:
http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.1.0%2Fnrfx_migration_user_guide.html&cp=4_0_0_2_5...
Hello,
I found the link below and was wondering if the information is up to date (says nRF52 SDK v0.9.2 ).
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic...
Hello,
I am using nRF52480, s140 , SDK_15.0 and using a central example. I can print the scanned RSSI, and MAC address of the each advertising packets with BLE_GAP_EVT_ADV_REPORT...
Hi, I'm trying to increase the NRF_SDH_BLE_PERIPHERAL_LINK_COUNT to max possible (20) in my project. When I first tried to do this the softdevice prompted me with this error...
Looking to better understand bsp_indication_set.
As per the example custom_ble_service_example found on github, ...when DK is connected, LED_1 is lit and stays lit from...
Hi,
I'm developing an application for nrf52840 that's essentially based on both the USB MSC example and the BLE NUS example in SDK 14. I started with the USB MSC example...
Hi,
I am using sdk 14.2.0 ble_app_hrs_freertos example.
two threads i have created, threads are having nested loop inside.
for this case, thread is stucking inside loop...
