Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi everyone;
I wanna send to data my uC from my phone. I looked peripheral uart example. This example use only send data phone from nrf52 SoC. What can i do? How I add...
Hi All
I have developed some code by modifying the 'ble_app_multiperipheral_pca10056_s140'. I have tested my code on the NRF52840 DK board (PCA10056) and everything seems...
Hello
I have developed an application for the smart beacon and I have the following problem:
I use two diferent sets of values for the connection parameters in order to...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
We are developing a BLE Mesh product and we use the mobile phone mesh library iOS and Android for the node provisioning.
The final user will need to synchronize more than...
Hello,
We have a Buttonless custom board based on a nRF5282 with SDK 15.0.0
The DFU OTA Buttonless works fine, but to prevent the device to brick we put a physical button...
Hi all,
I am having build error of example light_switch_dimming_server in mesh sdk 2.2 that timer 2_irqhandler multiple define it is define in
D:/../../nrf5_SDK_for_Mesh_v2...
Hi.
I'm struggling with BLE example projects on the my custom board.
my board uses nRF52832-QFAA, 16MHz external crystal with no 32,768kHz optional RTC.
and I choose...
There appears to be a conflict between ble_advertising and broadcasting while connected. If connected, the ble_advertising state machine still gets TIMEOUT messages from the...
I am working on light switch demo of mesh SDK 2.1.
I am using nRF52832 board, SDK 15 for softdevice and segger embedded studio for programming the nRF52832.
I programmed...
Hello everyone,
I want to develop an android app, which is able to control multiple LED Lamps in a Mesh Network.
There is an app for provisioning provided by Nordic. Is...
Hi,
When I call sd_ble_gattc_read , I receive the BLE_GATTC_EVT_READ_RSP event very shortly after -- as expected. Within the event handler (registered with the Soft Device...
Hi,
I am considering using baluns instead of discrete components next to my nRF24LE1 QFN-24 chip since board space is at premium.
In application note AN4111 regarding...
I am new to Nordic and have a simple question. I followed the instructions about setting up manufacturer specific data with BLE_Template example here: https://devzone.nordicsemi...
in the middle of the code the MOSI change from idle low to high and resulting in writing 0xFF while reading over MOSI, resulting in getting wrong data. how can i change it...
