Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
My target is to update the application firmware running on the nRF module using serial wire connection.
I currently do experience the issue, that DFU process completes...
I am in the initial phases of porting an arduino project using the NRF52832 to the Nordic SDK (14.2 for the moment) and am running into issues when using TWIM and an event...
Hello
Im trying to figure out where the health model client sends the health messages. Ive tried doing prints in all of the send methods in health_model_client.c but not...
Hello,
I'm having an issue when I try to connect to my device from an iPhone X. I'm using SD132 v6.0.0 on SDK 15.
The phone tries to connect and then it times out. All...
Hi!
After connected and get log info "Connected." I start bonding:
but there is no any success message.
Therefore nRF52 SDK15 can't to made secure bond.
Why?
Hi,
I'm using the light_switch example to implement mesh. How do I display the RSSI value of server on rtt viewer when the client receives the server status?
Regards,...
Is it possible to modify BLE_CONN_CFG_GAP after the softdevice has been enabled? I want to be able to set the event length on start up based on a setting stored in flash with...
Hello everyone, I am looking to make a small tracker using nRF52832 chip. Can anyone please suggest me a board and a coin cell having very small dimensions so that my tracker...
I am looking for a solution to create a very low latency (<10mS) audio link for continuous streaming.
Is the proprietary mode on the nRF52 series able to do that?
Is there...
hi
In Provisioner
in function app_default_models_bind_setup()
check the following lines
/* Bind health client to App key, and configure publication key */ ERROR_CHECK...
Hello,
I am creating a project through the MultiLink example.
One problem occurred. If the device is attached to NRF52DK, the connection will be disconnected immediately...
Hi,
I am running nRF5_SDK_15.0.0_a53641a\examples\peripheral\usbd_hid_composite and find it can work in standalone mode. However, if I go to Keil or IAR debug session...
I created mesh networking using mesh SDK v2.0.1. And I have connected mesh to PC and smart phone.But it's a pity that the client can't receive the servers' RSSI (although...
Hi,
Need ESD protection recommendation for NRF51822.
While testing nrf51822, we noticed that when SWDCLK gets static dicharge over 900 V, nrf51822 reboots and current...
