We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
hi, i am getting start nrf 51822 BEL with ble_app_uart
as a first step, i just compile the one of the BLE example 'ble_app_urat" which is located in 'C:\Keil_v5\ARM\Device...
I have a project that uses the nRF51822_xxAA chip with a pull-up button connected to pin 9. Using a meter, I have verified that the pin drops low (0 V) when the button is...
Hi,
I'm reading temperature and humidity from 2 sensors in my system
At some point in time during a quick and dirt check the system has been proven working fine and...
HI:
everyone!
How to make the matching and binding equipment information would be stored permanently, even after the OTA upgrade is still in;I made with examples of the...
Greetings, I tried to modify the parameter "len" to anything over 1 (byte), but it just doesn't work.
As long as it's over 1 byte, the API crashes my program. err_code shown...
Hi,
I'm using s130 as softdevice for nrf51822. I program the softdevice with the official s130 hex file. According to the hex file, there is no data at address from 0x7c0...
We're working on an application that needs ultra-short range BLE, on the order of 50cm radius or less. I've found little discussion anywhere on that topic, likely because...
I notice that the dongle has a 3.6V-5.5V input and a pin that sais 3.3V, I measured 3.3V on this pin so I was curious if I could run an IMU unit and an i2c/spi bridge requiring...
Hii all
I am trying to port the experimental/bootloader_signing project to gcc I made changes in the project accordingly, so now its working. I can able to flash application...
I connect a GPS module to nRF52 DK and connect nRF52 DK to my computer once more.
GPS module ---> nRF52 DK ---> computer. (like this)
So I want to do NMEA parsing like...
Dear All,
I am sorry but I have to ask this question here, I searched and red trough the forum, tried the suggestions, nothing works.
Basically I want to have a HID device...
I use softdevice 6.00, size is 80K Byte. I use the chip NRF51822ab,and configurat the irom start at 0x14000,size 0xC000, IRAM, start at 0x20002000,size is 0x2000 ,in keil...
Hi,
Is there a possibility to read the state of the gpiote pin? (is it high or low). Is there any function or any other way to do that?
I'm changing the gpiote pin via...
Hi,
I made a own service for a rotary dail in a peripheral(S110). This service send the speed, direction and a counter (all uint8) of de rotarydail in separate characteristics...
Hi Everyone ,
We were using nrf51822 rev1 IC for our project and now it is changed to nrf51822 rev3 . Previously we were able to detect the chip in nRfgo Studio on our...
