Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi,
I was successfully changing mac address dinamically DURING ADVERTISING on nrf51822 chip at each ble_radio_notification event, in this way:
Before start advertising...
Hello
How do I activate Brown-out reset? I estimated there need to set some register/registers, but I cannot findout.
Possibly Brown-out reset function is always enabled...
Hello,
I work on project for BLE communication in DFU mode.
I am testing according to the mode defined on the Nordic web page link
I did the tests with the BleuZ and...
checking most of the reliable coin cell CR2032 such AS Panasonic declare on very very low current transfer far lower then 5 mA
if i set my Ble in 5mA IO OUT ....when my...
NAND or NOR flash memory to use with nrf25832? my application is to store the data from mpu-9255 to flash memory. my data rate is about 3 mega byte per hour and i have such...
Hi,
I am using Linux ubuntu 14.04 with kernel version 4.15.0-041500-generic for 6lowpan over BLE and MQTT broker wit IPv6 address as inet6 address in below image
In...
If I use DeveloperStudio_1_1_3139_0 to generate a profiles and services for the latest SDK 15.x, will it correctly work?
I recall back with SDK 11/13.xx it was not compatible...
I need to sample ADC channel at the fastest deterministic rate.
If i use burst mode with 3us acquisition time, do i get a sample exactly every 5us?
does t(conv) is always...
About example BLE_uart,
My device must always remain in advertising, I'm using a 1280 ms between two advertisng event.
I have to minimize the consumption during advertining...
I have a few questions about the NRF6707 Power Profiler kit and I would like to ask you: 1. The NRF6707 Power Profiler kit and nrf52 DK are linked through the ARDUIND D0 pins...
I am updating the application software that was created based on ble_app_multilink_central in SDK 9.0 to 12.3. When replacing device manager with peer manager, I received...
I'm just getting started with the Nordic chips so I will apologise now if I have failed to find my own answer amongst all the devzone content.
I want to use the NUS service...
Dear all,
I have a problem with secure connection between Android (nRF Connect) and my custom board with nRF52832. I'm usind SDK 14.2 and SD_132 v.5.0. I'm using secure...
Hi All,
Anyone know the aggregator example can run on the nrf52 PCA10040 DK?
https://github.com/NordicPlayground/nrf52-ble-multi-link-multi-role I fail to compile the...
I've got a bit of an issue with turning off specific debug statements. If I try and adjust the log level, I get a run time failure. If I try and comment out the specific debug...
