Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi Nordic Team,
I’m working on a battery-powered Matter-based project using the nRF54L15-DK. I’ve reviewed the documentation regarding power optimization, which recommends...
Hi,
1. It was measured that SWD0_SELECT needs to be connected to VDD to program the external nRF54L15 2. Will the document or the program be modified here to make it consistent...
I have already written the factory data to the device, and commissioning via Apple TV is successful.
It also works when using the --bypass-attestation-verifier 1 parameter...
I was following instructions from this and this post, but I'm not yet able to build with the following combination: CMakePresets.json + west + sysbuild.
I'm using this west...
Dear Onomondo Support Team,
I am currently experiencing an issue with my Onomondo SIM card — it is unable to register on the network when used with the nRF9151 DK board...
NCS 2.9.1 - NRF5340 DK
I've developed the gppi one_to_one example to try and create an asymmetric pulse that I can control with the Timer compare registers. It boggles my...
I am following along this example on your website: Exercise 1 - Nordic Developer Academy , and currently trying to complete this excercise: Exercise 1 - Nordic Developer Academy...
Hi, I tried to migrate my project from nRF Connect SDK v2.5.3 to v2.9.0, switching to sysbuild and creating my own board definition instead of using a overlay file.
I decided...
I have a custom board (nrf5340) and can debug it, but it will not print to J-Link RTT Viewer. The main looks like this and I tested with a breakpoint on the LOG_DBG using...
Hello! I'm looking for a way to include fast charging capabilities in my product, while still allowing USB2 data to pass between any host PC and the nRF52840. As I understand...
Hi, I have custom board with nrf54l15. Im using sdk 2.9.1 and nRF54L15-DK as debugger/flasher. Im able to flash firmware correctly using SWD, or do nrfjprog --recover, but...
According the nPM2100 page "nPM2100 comes with exceptional software support for Nordic’s nRF52, nRF53, and nRF54 Series" but doesn't mention "nRF91 Series".
Currently I...
I need both zephyr power device management and the low power features of LPUART in my project.
However, enabling PM_DEVICE raises idle current consumption by quite a bit...
Hi,
I want to produce a pulse with 4 seconds length from p0.25, but i am failed.
#include <zephyr/sys/printk.h>
#include <nrfx_pwm.h>
#include <hal/nrf_gpio.h...
Hi, I would like to have some suggestions on my PCBA design for nrf54L15 chip. Please review it and give some suggestion moving forward. I am making this PCB to use this with...
