Hi There,
I am using a nRF52840DK board to experiment with NFC Tag technology.
I started with the "Writable_ndef" example inside the nRFConnect, and it works.
I wrote...
Where can I obtain the security certificates (e.g., client certificate/private key) needed for TLS authentication with nRF Cloud? - Are these generated during device onboarding...
I plan to use my own SIM card (not from Ibasis). Could you clarify how to register the device in nRF Cloud to enable A-GPS services? - Should I link the device’s IMEI or ICCID...
Hello, I am developing nRF5340, the project is pre-production. I am getting a issue with BLE power consumption, when I turned BLE on, the current is about 9uA. with BLE beacon...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi,
Having worked with your software on and off for some time now there are a few things I have noticed that are slightly disturbing when it comes to the SDK.
Usually...
I am doing a register retention gzll transmit code with ADC. But problem is that the ADC value transmitted is always 255, if I connect ground to ADC it would read 247. Why...
Hello,
I am using nRF52480, s140 , SDK_15.0 and using a rscs central example. I used
uint32_t current_time = app_timer_cnt_get(); NRF_LOG_INFO("current_Tick: %02d", current_time...
The function nrf_qspi_cinstrdata_get has logic bug that didn't combine data from both register
https://github.com/NordicSemiconductor/nrfx/blob/master/hal/nrf_qspi.h#L702...
Hi,
I'm trying to notify some sensor data at a constant 25 data packets per second.
If I set the `MIN_CONN_INTERVAL` to `10 and `MAX_CONN_INTERVAL` to `30` it all works...
Hi All,
I am developing a BLE central peripheral application by using ble_app_hrs_rscs_relay (nRF5_SDK_15.0.0_a53641a & s140 softdevice) on nRF52840 DK board.
My issue...
Hi,All
My case is that we need 20 peripherals connect to multilink central and send data to central,then central device need send data to Pc with Uart.
The current situation...
Something easier/faster than this? https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader
The procedure described in that link...
I added bonding/authentication to my application.
I have two characteristics: a "protected" characteristic (cccd_md.wr_auth = 1;) with indications and an unprotected characteristic...
Hello!
I have very strange issue when same firmware works fine if it is flashed using segger debugger and randomly fails (with device restart) when it is flashed using BLE...
We have been using the Nordic PPK to optimise the power usage of our nRF52840 based application - very useful tool.
However, our application changes modes over time (e.g...
I have a local ipv4 network with a Mac laptop. There is a Raspberry Pi Thread border router connected to the network. There is an nRF52840 running the Thread CLI example....
