Hello,
I higly need to run twister unit tests in debug mode with breakpoints, step by step, spies and other debug tools in vscode. I did not find a way to do so.
Is...
Dear devzone, Can our nRF52840 detect 20 nanosecond voltage fluctuations using COMP? For example, if I set a lower threshold of 20mV and an upper threshold of 60mV, and the...
Hi nordic： What is the peak current of NRF9151? The relevant parameter cannot be found in the datasheet, while it is available for NRF9160.
Best Regards
JERMI.JIN
I'm using the nRF52840-DK part number 1490-1072-ND I ordered last week. In both nRF Connect for Desktop and the VS code extension the device wasn't able to detect. Tried two...
Hello, this is probably a very beginner question but I don't know how to configure interrupt for the GPIO headers on the nRF52840 dev kit. I tried to search in this forum...
In the documentation for the secure bootloader, it's mentioned that the provisioning data gets stored in OTP memory for some chips (e.g. nRF5340). Is there a way to know what...
Hi:
I don't receive any messages in the console during any of the exercises in Lesson 3 and Lesson 4 of the nRF Connect SDK Fundamentals.
No errors occurred during the...
I am using nRF5_SDK_11.0.0_89a8197 to test esb maximum throughput.
in the macro definition of NRF_ESB_CREATE_PAYLOAD,
#define NRF_ESB_CREATE_PAYLOAD(_pipe, ...)
...
On the nRF51, there are 5 OVERRIDE registers (0-4) in the radio module.
What do those registers do and when should they be used? The FRM was not clear about them.
From what I can see the scenario where you have a serialized app running from a separate CPU and how to do firmware update on that is not discussed anywhere on the Nordic...
ToSendTONordic.zip
Hi,
I am using s130-nrf51822xxa. I tried GPIOTE example and it works fine. I tried ble_uart example and it works.When I try to combine both of them...
As of API level 21 BluetoothGatt#requestMtu can be used to go beyond the limit of 23 bytes GATT_MTU_SIZE_DEFAULT. Will the SDK support such enhancements one day?
In BLE notification i am getting 31 byte data but it comes in two packets 20 byte + 11 bytes continually.How do i get last 11 byte data which comes in 2nd packets after 2s...
Hi,
i want to test the Server feature of the Master Control Panel 3.10.0 together with a nrf51 Dongle. By pressing start under File->Server setup the server starts, but...
Hi I have problem with LFCLK timer. In os_tick_init() in RTX_Conf_CM.c there is a loop and it won't end.
while (NRF_CLOCK->EVENTS_LFCLKSTARTED == 0)
{
Do nothing.
...
gaps.zip
Hi,
I have a code that continuously toggles a pin(I use nrf_drv of gpiote+ppi+timer2 for this purpose and interrupt time = 30usec). I have basically taken the...
I know the things like the TWI allow you to send additional data when you instantiate a transacation. Is there any way to do a similar thing with UART?
I'd like to pass...
Hi
I'm using the PeerManager/FDS/FStorage in my project since a few months. We have this software running on real hardware and on simulated environments. While researching...
Hi NORIC's Engineers:
I am a handware engineer who is from Jetway company in China.
I am sorry for my english skill to descripe my questions about NFC antenna of nRF52832...
Hi!
I'm am working on a project where there I need to connect two nrf51 modules and a phone.
Say: Module A, module B and phone P.
The setup i a bit tricky to explain...
I want to use three ADC-inputs on my nRF51832 Engineering Sample B. I read that it is possible to define several ADC-Channels and if a ADC Sample is triggered all Channels...
