I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Hello,
We’re Bachelor’s students developing a project to estimate the angle of arrival (AoA) using a BLE antenna array on the nRF52833. Our implementation builds on Zephyr...
Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
Hi,
Right now I'm looking down at the nrf52840 datasheet, because I would like to do a project with such MCU, but I got to the part of the integrated DCDC converters and...
I noticed that flash error logging was taken away since pstorage was added (sdk v5.0.0 and softdev v6.0.0.1-beta). Will it ever be added back?
If you say that it'll never...
I'm using the nrf51822. and then I tested the samples to receive the ANCS and send to iPhone information of temperature sensor.
I would like to merge the two above-mentioned...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
I have the nRF51822 Evaluation kit and put the Heart Rate Demo on the PCA10001 (V2.1.0). When I press Button 0 it doesn't advertise. I have the module (PCA10000) scanning...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
I copy static void radio_disable(void) and void radio_tx_carrier(uint8_t txpower, uint8_t mode, uint8_t channel) into my project.
I call radio_tx_carrier(RADIO_TXPOWER_TXPOWER_0dBm...
Hi all,
I have a spurious crash in the softdevice I guess.
It occurs sometimes when the master (an HTC-M8 android phone)
rapidly submits characteristic changes
(acknowledgement...
SDK: V6.0
HW: PCA10001
APP: s110/ble_app_hrs
Question:
If use "twi_master_init()" with "twi_hw_master.c", the current consumption is added 1m
A. But if use with "twi_sw_master...
Hi I am completely new to ARM development world. I have been developing for years for PC.
Now I am working on a Project where we have decided to evaluate nRF51822 chip...
I would like to know if it is possible to use the internal RC oscillator without calibrating every 4s with the softdevice disable. I just want to read a sensor every 2s and...
I'm interested in using BT LE to collect data from a number of serial based devices -- a point-to-multipoint configuration. I'm familiar with the UART examples and have seen...
Hi,
i am searching for infos about my concrete BLE-Sig certification situation but i cannot see the forest because of all the trees :o)
i am currently developing a BLE...
Hi,
I know that a lot of question exists on that subject, but I can't manage to have an accurate battery measure on [Nordic Beacon device] (battery CR1632 3V) ( www.nordicsemi...
