Hello,
I'm here again because this time I need to autoconfigure (configuring from inside program, no use of any nrf app) heartbeat destination node and source node.
For...
We have developed an application which uses the nRF9160 together with the same GPS and Ethertronics/Kyocera/AVX antennas as that of the nRF9160-DK . For the LTE antenna, we...
We're trying to measure supply current used by the NRF9151 DK but have discovered that the current measurment connector (P22) only includes current supplied to VDD, and that...
Hi,
I'm using the nRF52833 to develop a BLE beacon and built a Bluetooth gateway for my application.
Application Requirements:
The beacon should advertise using...
Hello,
I want to perform some antenna measurements and compare the rf performance of my custom PCB with an nrf9160 SiP with the nrf9160 dk.
To perform some antenna measurements...
Hi I want to build a multi role BLE device.
As a peripheral it shall stream ADC data with arounf 20 kbytes per second.
As Central it shall receive adv_nonconn_ind packets...
We used nRF5_SDK_15.0.0_a53641a and nrf5_SDK_for_Mesh_v2.0.0_src.
We are following DFU quick start guide http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Dear Sir：
i seen the proximity example，the battery level measure is init by a m_battery_timer_id ，in my project ，
i need user multi saadc channel ，and different...
Hello, we are using the nRF52832 for building our custom board.After loading the example bluetooth_uart code given in the SDK, our board is not producing correct RF(Bluetooth...
Hi, I have a BMD-300 (nRF52) module that I'm attempting to program with OpenOCD and an ST-link from Linux (it worked great for nRF51 so I was trying to keep the same tools...
Hello,
I have been trying to have a central/peripheral device read UUIDs and RSSI values from surrounding peripherals using their advertisements and without actually connecting...
I'm attempting to add the bonding components from the ble_app_hids_keyboard example to the ble_app_uart example. I've gotten everything configured to the point where I can...
I am connected with this correct com port but Device discovery is failing to start.
First it says NO response from master emulator then it fails to start. Please help me...
Hi, I see that in the nrf52810 reference layout ( Nrf52810 Reference Layout ), all the capacitors and inductor have 0402 or 0603 footprint. i would like to switch the foot...
i followed this custom service tutorial.
but when i changed the RAM_START and RAM_SIZE address it getting below error, im using S132v5 softdevice
<warning> nrf_sdh_ble...
Are the PCB antennas provided in eagle library of NRF52810 ( github ) require any additional components for impedance matching or i can directly add the PCB antenna to ANT...
I downloaded radio_test.c from Nordic and complied it to output a .hex file. Now I want to flash this .hex file onto nRF52832. Does it require to softdevice and bootloader...
Hello (I'm new to this nRF-world...).
I am searching for a small "nRF-52832 clock" (arm mounted watch) that at least reports the "surrounding/room temperature" (not only...
Hello
SDK12.3, nRF51822
Example Gazelle from SDK works fine. If I use the softdevice (add ble_stack_init) then the program freezes in the nrf_gzll_enable
I want to do changes for firmware upgrade nrf52832 with SDK BLE_2.0.1 for the mesh.
I need DFU (Bootloader)UART for our application to upgrade nrf52832 firmware by the host...
Hi
I have written this code based on a sample from SDK12. The board is a pca10040 and nRF52832 chip. It seems like after disconnection from the master device the Softdevice...
