Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
The nRF5 SDK is event-driven. So does it mean that the event handler in my application will be directly called in the interrupt service routine? If I write a long event handler...
Hi all,
I'm experiencing a performance drop with BLE proxy enabled in Mesh SDK 2.0.1 compared to Mesh SDK 2.0.1 / Mesh SDK 1.0.1 without proxies (higher packet loss, range...
Hi,
I have project for NRF51822 in IAR(EWARM). Short about project: it based on example BLE to UART communication; it uses SPI, I2C, analog inputs readings, some digital...
I used nRF5_SDK_14.1.0_1dda907.
I opened the bpwr channel then received ant+ packet.
The device received ant+ packet successful.
How do i know that how long time the...
hi all ,
how to build multi provisioneers with mesh network ?
i read some information and run the nordic mesh sdk 2.01 (ligh_ swith sample )
i have some issue with...
1. I am issuing a gatt characteristic (CHR1) write without the response requested from Central (BLUEPY/BLUEZ, Ubuntu 18)
2. Central than reads CHR2.
Is it possible...
Hello,
If I understand well, when the part of the flash reserved for the PM is full, new bonds cannot be saved until the application deletes older bonding data.
I would...
Hi,
I've heard some stories that that using analog capable pins for digital IO (UART in our case) results in significantly higher power consumption than using a pin that...
I've modified the app_timer library slightly to keep total system uptime, which I can use to keep calendar/epoch time if initialized with the current time from an external...
Hi Everyone,
I examined the document about nRF24LE1 FOTA "nAN18 - nRF24LE1 firmware update over-the-air". The document is about update firm by nrf24lu usb rf adaptor. I...
Hi,
I found some sensor drivers under nRF5_SDK_15.0.0_a53641a\components\drivers_ext\, like hts221, lps22hb and so on.
Where can I find example for those driver?
Regards...
Can someone please clarify a few things!
I'm trying to get high bandwidth on some to and from phone transfers. I have control and data gatt boxes, control has the connection...
Hi,
i am doing a project where i have to discover multiple custom services on connected ble peripheral from ble central device.
i am using nrf52832 with sdk 14.2.0 as...
hello,
Now i have two troubles in NRF52832 Gateway.
1.Planning introduce：
The only function of NRF52832 Gateway is to scan beacons' advertisements. With beacons‘ number...
