When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi all,
Going through the sniffer document and devzone tickets, I observe that there is no official nRF sniffer software to emulate nRF52840 QIAACA SoC as BLE sniffer. ...
Hi Everyone
I was trying to use segger embedded studio for nrf52840 PDK.
I could get the example codes working but when i tried to create a new project and try to include...
Hello, I am trying to initialize the service Power Cycling from the files of this link https://devzone.nordicsemi.com/f/nordic-q-a/9169/cycling-power-service-0x1818
I get...
Hi,
I've been trying to use the nordic power profiler v1.1 with my nRF52 development board to figure out how much current is consumed during operation.
I used the power...
In the light-switch-proxy-client example there is every unreliable group message repeated a number of times (GROUP_MSG_REPEAT_COUNT). Is this always required to be implemented...
When the nRF53832 is connected with a cell phone for data transfer, can it still be discoverable, and go though pairing/bonding process with another cell phone? I think the...
Hi, Just porting an old project from nrf52832 to a nrf52810. I've had trouble finding a bare-bones project (arg-gcc), basically just main + log for the 52810.
I understand...
I have four Bluetooth modules (servers) that measure pressure continuously. The servers should connect to the client and send the measurement data to the client. I can read...
Good afternoon,
We are developing a consumer product that is using the nRF8001 as the BT peripheral. We have a question regarding certification; do we need to undergo...
Dears，
To support Bluetooth 4.2 in the nRF51822 product page on S110, but only support 4.1 in the SDS document, I want to confirm the support of the S110 V7.3 and v8.0 for...
Hi,
for my application, I want the processor to wake up once every 8 hours, do a 1 second analog measurement, broadcast the results and shut down. When activated by a switch...
Hi,
I am having some trouble using fstorage to write data into flash. I want to store ~20 kB of sampled data before processing it, and I am storing it just below the bootloader...
Dear every one.
My company has ordered 20 development kit NRF52840 for our Mesh project. We will receive these board 1 week later.
But i have 1 preview development kit...
