I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Does the nrf Mesh Android App/iOS supports Extended Packet Length? Like MTU size > 23 .
I have used Samsung Galaxy 8 but I am not able to provision the Device , even though...
Hello,
I want to use ANT+ communication on the nRF51-dongle that has a PCA10031. I have downloaded the SDK 12.3 to use. I have used some of the BLE examples before that...
Hi all, in new update app NRF Mesh Android, I can send data from Android app to Kit run light switch proxy server in SDK MESH V2.2. But It using generic_on_off_server. So...
My setup is a Android phone, Nordic NRF52, and random BLE devices in the area.
What I want is, the Android NRF-UART app connects to the NRF52 and the NRF52 sends information...
Hi,
i use the Aead-Lib for CCM on the NRF52840. What is the best way to Check an Mac from a Message wich only has Adata (no acctual encryptet message)?
If i try to use...
Hi,
related to a previous question I posted, , we are migrating from nRF5_SDK_13.1.0_7ca7556 to nRF5_SDK_14.2.0_17b948a.
Now we have some problems with the bootloader...
The subject really says it all; why are there four GPIOs tied to P0.18 which is the nRF52840's RESET# pin?
I'm looking at the PCA10059 Schematic available in the nRF52840...
I am currently using the nRF24L01P in an application where I am using the RPD feature to determine whether a 2MHz RF channel is "available". For example, if a wifi network...
I am using nrf52832 and I am trying to interface OLED with it. I am attaching the code below and i referred that code from https://github.com/devdprj/olednrf here,
i made...
Hi All.
I have a DK52 project where a peripheral advertises and connects to a central nRF52840 ok. I based it on the multilink_central demo, so have the LED button service...
Hello!
I went through the example project "Experimental: ATT_MTU Throughput Example" provided in SDK v15.2.0 and found that there is a configuration bit in BLE_COMMON_OPTS...
When I connect to my device with an iPhone, using the nRF Connect app, I am experiencing an immediate disconnect. The part does not have time to start pairing. I have shared...
【Question】：I want to use timer+ppi+SPI(with DMA) write DAC, but now something is wrong, when timer trigger the SPI to write DAC through PPI, it can call the "spi_event_handler...
Hi,
I use UARTE peripheral when i communicate wih PC.
This code works. Send 4 bytes.
bno_tx_buf[0]=0xAA; bno_tx_buf[1]=0x01; bno_tx_buf[2]=0x00; bno_tx_buf[3]=0x01;...
