I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
I am running the examples l9_e5, l9_e5_sol and l9_e5_nrf5340_both_sol from this repository: https://github.com/NordicDeveloperAcademy/ncs-inter/tree/main/v2.9.0-v2.7.0/l9...
Hi,
i am working with the following setup:
- nrf5340
- SDK 2.6.3
- Direct Test Mode example with serial communication
I see that DTM example has changed from 2.1...
Hi Nordic team,
I'm implementing a BLE UART bridge (emulating the old SPP profile) using a custom service. The central device (dongle) I'm using only supports the classic...
Hi guys,
I am following DevAcademy lessons on nrf52833dk kit. I am testing the software on VsCode. SDK version is 2.7.0 and toolchain is 2.7.0. Board target is selected...
Hi Nordic Team,
I am working on matter-based product development using nRF54L15 and looking for machine learning support for the same SoC. Can you please confirm if machine...
How do I adjust the swd speed used by nrf connect RTT ? Currently it is 2000khz but more is needed. I need to transfer audio data to PC.
For some reason my current process...
I saw in nrf connect sdk 2.9.1 that there was nRF54L15 sample code for Channel Sounding and nRF52833 DK sample code for Direction finding.
But now I want to implement...
Hello,
I am attempting to configure the following setup to support (with an nRF5340 + nRF7002-EK)...
1. nRF7002 on SPI w/ TLS, STA, and FW patches offloaded to QSPI...
Hello,
I am using PAwR (Pe riodic Adve rtsing with Response) in coded PHY (S8) with SDK 2.7.0, following the Nordic demo :
8562.PAwR_Demo.zip
Periodic Advertising with...
Hi all,
I'm working on a BLE peripheral using Zephyr and have run into an issue when enabling both dynamic device naming and long advertising intervals.
I enabled dynamic...
Is there a way to test that the RXD and TXD pins are sending and receiving data on the nrf5340? I am trying to connect these pins to the u-blox ANT-B10-00C using male to female...
Hi guys,
we are using the nRF52833 and have a running application. Now I want to introduce unit tests and stumbled upon ztest . The idea is to add a folder where all the...
I'm using nrf52832 developing my application.
In the past I used sd_ble_opt_set() to set a static pairing code for pairing.
But now a new requirement has emerged, I need...
I am trying to develop Zigbee plug using the demo provided by Nordic. Working on my Intel Macbook Pro 13.7.3
The toolchain and SDK are installed, ver 2.9.1. The program...
