void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
hi ,
I have a project with sdk14.2 nrf52832. It works well, it can broadcast, it can connect, everything is fine.
But I have a new project that requires nrf52840. My...
Hi i am trying to do DFU boot-loader in nRF52832 and i am following all the step that you have provide in nordic developer zone ( https://devzone.nordicsemi.com/b/blog/posts...
When using my mobile to make provisioning with the GATT provisioning example for the light switch, is the mobile a node? Does it get the messages as well? Does it work as...
I'm under the impression that this piece of the given example is an interrupt handler. Am I correct? If yes, then there another snippet:
So, is there a while loop inside...
Hi All,
I am facing problem in my bootloader linking please see below
Linking target: binaries/bl/bootloader.out /tmp/cc9UGLw7.ltrans4.ltrans.o: In function `nrf_svc_handler_c...
How do you think - is there resources enough to add SPL (sound pressure level) measurement functionality into Nordic Thingy:52? Is microphone appropriate or may be external...
Hello, I'm using the example package Nordik_Mesh_V2_0_1 \ nrf5_SDK_for_Mesh_v2.0.1_src \ examples \ light_switch, and I would like to extend the number of servers from 4 to...
I'm trying to understand the cost differences, and pros and cons between:
A) creating a two chip solution - Using a BLE module - PLUS an second micro that runs my application...
I am in the process of trying to send live data from a nrf52 board over bluetooth to another nrf52 board using the example projects ble_app_uart_c and ble_app_uart. We are...
Hi,
I use SDK 12.3 to run experimental_ble_app_buttonless_dfu on nrf51822 after reference this blog , but still can not work.
It works fine with PCA10028 board.
I want...
hi :
i send characters of SPI master of 52DK to SPI slave of our target board(Nordic nRF52832), our target board use SDK v12 spis example. but spi slave event can not rececive...
I am using SDK 12.3.0 and S130 2.0.1.
In example ble_app_uart and ble_app_uart_c,
Central setting:
Peripheral setting:
Why it took so long to discover service...
Using the same connectivity firmware, a dfu update using nrfutil takes about four times as long as the same update using nrf connect. I have to setup dfu updating in a production...
Hi,
I am trying to communicate with a Wi-Fi module external to nRF52840 via UART. I am using the nrf_serial_read() API. I have tried different values for UART baud rate...
Hello, I am trying to broadcast a data among 2 receivers with a special ACK payload. I transmit and gather ACK with one receiver properly yet m_nrf_esb_mainstate locks in...
