Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hi,
want to try out the nRF52x Family, so will buy the DK board, which IDE is recommended? I am familar with VS Studio or Atmel Studio 7, so is there something like that...
Hi:
I want to capture the parameter of a digital wave like this, I want to get every 't' value. The wave is same in a period of time, but the 51822 capture value of 't' is...
SDK: 10.0.0
Softdevice: s110_nrf51_8.0.0
I'm working on migrating our application from SDK v9 to v10. I'm getting a softdevice assertion failure in src/rem.c line 1371...
Hi,
Can I use power profiler kit for current measurement of nRF52840 SoC?
If yes is there any hardware and software revision version(s) for power profiler kit?
Please...
I created a BLE Peripheral to read the light intensity, the purpose is connected to the iPhone device to read the update value in the BLE_NRF_52 device.
For the calibration...
Hi,
I checked this thread https://devzone.nordicsemi.com/f/nordic-q-a/24611/how-to-change-the-name-of-bootloader-s-dfutarg which suggests to modify the macro but I would...
Hello
for my project at the university I have to implement a bluetooth mesh network using 4 nordic thingys:52 and one nRF52DK(only for programming purposes, not part of...
Hi All!
I use Example Project from SDK: "examples\peripheral\usbd\" as reference to implement my HID device simple protocol (EP1IN / EP1OUT 64bytes)
The Question is how...
I am working with the BL652 Module from Laird, and with Keil 5, using a ST Link SWD programmer clone.
I am using the ble_app_uart_timer_driven_scan_mode from the ADC examples...
Hi, I am developing an IoT sensor (peripheral device) using SDK v11.
On my sensor, I have defined an advertising packet that broadcasts the complete local name and a scan...
I'm in the process of porting my application from SoftDevice S132 v4.0.2 / SDK v13.0.0 to SoftDevice S132 v6.0.0 / SDK v15.0.0. I noticed that the define for BLE_GAP_TIMEOUT_SRC_ADVERTISING...
Hello,
I'm attempting to use a high-limit reached event from the SAADC to trigger the clearing of a GPIO. My wish is to disable this GPIO with the lowest possible latency...
I used SDK 13.x to create a custom profile with services for nRF52832 with BLE 4.2
If I go to a nrf52840 with BLE 5.x SDK, can I use the exact same code, or do I have to...
