Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Error executing NovelBits Gateway app on nRF52840 with SEGGER Embedded Studio. "Cannot connect to J-Link via USB" Running the SES for ARM 3.40 on Ubuntu 16.04 64 bit. The...
Hi,
We want to send our pre-production ready product for compliance testing. Selected testing laboratory told us " Conducted sampls should be set in continuous transmit...
Dear All,
so we have an embedded SoM running OpenWRT and I was wondering if I can make use of nrfutil even if not connecting a nRF52 via USB but via UART.
What I want...
So as far as I can make out, when I load a new application into the flash, the NRF52 will attempt to first load a secondary memory space and if successful, it will then replace...
Hi,
Right now i am using Blinky example in Peripheral section of SDK15 (S140). I would like to enable Coded PHY (BLE_GAP_PHY_CODED) instead of default setting (BLE_GAP_PHY_1MBPS...
Hi, I have problem with timer in nrf52810. My TIMER2 counts very slow. I declared it as NRF_DRV_TIMER_INSTANCE(2); and config struct is:
.frequency = NRF_TIMER_FREQ_16MHz...
Hi ,
I can compile and use the UART example but when I try to use it in my project I get some linking errors
I have copied and past all the sdk_config.h file to my project...
I am waiting for my custom pcb based on the nrf52832 to be ready and I want to test the flashing process. Is it possible to program a nrf52 DK with another nrf52 DK using...
Hello,
I was wondering if there is some way to program a device to act like a BLE slave, which would sleep and periodically wake up to stay in receive mode for a certain...
Hello, I'm confused what the NRF51422 uses for it's digital IO reference. So for example, If I use a 3.0V coin cell battery through its DC/DC converter: 1. What voltage does...
I download the SDK at https://www.nordicsemi.com/eng/nordic/Products/nRF5-SDK/nRF5-SDK-zip/59011 . When I used "nRF5_SDK_15.0.0_a53641a\examples\ble_central\ble_app_uart_c...
Hi,
I am using SDK10---->ble_app_uart--->pca10028--->s110 for non-invasive GLUCOSE measurement. I checked nrf_adc.h file & used adc_sample = nrf_adc_result_get(); for getting...
I am using nrf52832 development kit and softdevice v5.0.
I am using this code which I have attached.
I have added all require files.it might be not showing to you because...
My current setup is this:
I have a nRF51822 beacon (tiny coin cell beacon) advertising with its default settings. I have another board, a nRF51822 Development Kit, that...
