Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi All
I'm trying to measure the Ton and the Toff of a signal present on an input pin of a nRF51822.
The idea is to use PPI, Timer 1 and save timer on every falling/rising...
Hi,
we are using Linux machine and my application is running init, blue tooth stack is running on nrf52 board but after initiating the scan command we are not getting continuous...
Hi all,
I am using a linux based board and wanted to support BLE5.0 on that board. PCA10040 is connected with My board through UART. Please forgive me for these basic doubts...
Hi All,
Moto E4 mobile phones do not connect right away and at times takes few minutes and connects eventually. Right after I hit connect I get an error 0x85(GATT ERROR...
I am using Thingy (nrf52832) to advertise Eddystone UID and TLM packets in bursts. On a given event advertising starts with an interval of 200ms, then stops after specified...
My SPIM0 starts to use 300uA upon first usage of nrf_drv_spi_transfer. Why? Even when the transfer finishes and I uninitialize SPI or turn the MOSI, MISO and CLK pins to the...
Hi there ..
I have question regarding estimation of a coin cell battery life while advertising on nrf52840 PDK. I followed here https://devzone.nordicsemi.com/b/blog/posts...
Hello,
I am fairly new to developing ble beacon applications and was wondering if it was possible for my device to perform the following operations simultaneously:
Advertise...
Hello, my project is not going well. Trouble you Please help me again First of all, my English is not very good. I'm sorry. Can you provide an ideal sample code for me? My...
Hi
I'm using SDK 14.2, nrf52 DK and proximity example. When i try to write to inmediatte alert characteristic from nrf Connect ( android) i never get the event on the device...
Hi, in my project, the following codes caused "NRF_BREAKPOINT_COND":
sd_power_ram_power_set(4,(POWER_RAM_POWER_S0POWER_On << POWER_RAM_POWER_S0POWER_Pos) | (POWER_RAM_POWER_S1POWER_On...
I have secure DFU working fine for my s132 (SES sdk15.0), and now trying s112 using the example from post how to use dfu?
I used SDK_14.2.0_nRF52810_Secure_BL_v1.1.zip and...
