Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
I have TIMER1 configured as 16-bits wide with no prescaler (62.5ns tick) and CC[2] set up for a varying value near 65535. My work is based on the Nordic blog post about synchronizing...
When I use uart to transfer data, sometimes I get error NRF_ERROR_SVC_HANDLER_MISSING in APP_UART_COMMUNICATION_ERROR when I start sending data. Sometimes this error occurs...
Hey, can I use a complex structure (for example byte array ) as a message parameter instead of one byte like it is done in http://infocenter.nordicsemi.com/index.jsp?topic...
I have a Thread network setup using nRF52840 as per the documentation below, using the Raspberry Pi image provided by Nordic. http://infocenter.nordicsemi.com/topic/com.nordic...
Hi,
In my develop environment , there have many proprietary device. One device is working on PTX mode, and the other devices is working in PRX mode.
If the PTX device...
Hi,
In the FICR (INFO.VARIANT) register on the nRF52832 soldered on my board I can read: AAB0 and in the same register on the NORDIC DK I can read AAE0.
The only different...
Hi,
as described here https://devzone.nordicsemi.com/f/nordic-q-a/37056/supervision-timeout-and-unplanned-disconnect our device has a hard current limit of 2mA.
Problem...
I have a trouble in my project.After flashing softdeivc,I flashed my application,but adversting is not work immediately, then a turn off the hardware and wait some second...
Hi:
I am developing my project based on ble_app_uart example. The development bench is SDK13.0, the chip is nRF52832.
One problem I have now is that: I configure Pin12...
When using FreeRTOS, external GPIOTE interrupts do not work.
And just how correctly to use the NFC with FreeRTOS?
In examples NFC use app_scheduler for events handling...
Hi
I've done a few attempts in the last years to implement a reliable reception by using the UARTE. In the past we used the UART periphery from the nRF51, but we thought...
Hi Everyone
I have the following issue in my application code.
If i configure a pin as an input pin , i am not able to run the ble init function in which it advertises...
Hi team ,
i am vishal working for VVDN Tech .
we are going to use 10k parts of nRF52840in our project.
so we need step file of that.
Awaiting your soonest response...
Hi,
I am trying ble_app_uart example of SDK 15.
When I do not connect Uart port (TX, RX) to other peripheral, I get fatal error (log via RTT).
```
0> <error> app...
