Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hello,
I get "data_len_update failed (err -5)" error message in lesson 3 exercise 2 of Bluetooth course. I have posted the output log below. Any idea why this is happening...
Hello!
I would like to report a bug with the nRF Connect for VS Code extension.
My setup
VS Code v1.98.0
nRF Connect for VS Code Extension Pack v2024.9.5
nRF Connect...
Hello Nordic Engineers and community members,
I received an nRF7002-DK 1.0.2. (S/N: 1050757935), from Digi-Key today.
I've been following the YouTube video, "Getting Started...
Hi, We're using the nrf9160 with ncs 2.7, modem FW 1.3.6 We're trying to send an HTTP request with TLS 1.2. We have provisioned our device and verified the key,cert with a...
We are using SDK 2.4.0 and have enabled MCUBoot to support OTA updates using the dual slot method. I have reviewed many posts and existing tickets and have not been able to...
hello everyone,
I am using the nRF52840-QFAA-R7 (48-pin package) along with the nRF52840-DK development board. I have a question regarding I²C communication. Currently,...
Hello everyone, I am planning to make a wireless keyboard, and one of the requirements is that it has a long battery life, so I am very concerned about the power consumption...
So I've been playing around with some code example to make UART work (which I did eventually) using NRF SDK 5 (v17). However the last version of SES (8.22a) requires some...
I am having issues using a keypad to wakeup an nrf52840 and am unclear on if the GPIO sample is relevant if using a kbd_matrix device definition. I would like to use "sys_poweroff...
Hi,
I'm working on an nRF5340 + nRF7002 project using Zephyr RTOS , where the device enters low-power sleep and wakes up on a hardware counter alarm ( counter_set_channel_alarm...
I had been doing this:
What it does:
create a CHG (channel group)
DPPI is triggered by a GPIOTE in-event
DPPI then triggers and EGU, a TIMER capture, and...
DPPI...
Hi
board: nrf52832 DK
sdk: nrf connect sdk v2.6.1
I have successfully integrated the provisioner and light switch client together. Now I can control the light switch...
Good morning,
I would like to know if it is a good idea to store serial number on UICR register when using nRF9160 at production stage.
If using UICR, which register should...
I have compiled the sample code from ncs/v2.9.1/zephyr/samples/drivers/uart/echo_bot and loaded it onto an nRF54L15 dev kit.
The dev kit is connected to my pc running a...
