Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello Support,
We are doing a production test regarding the Radio test. On nordic SDK there's already a pre-build Example for Radio. I wonder if we can do the something...
Hi. I used a translator.
I used nrfutil to insert Softdevice & Bootloader into nrf52832 and then implemented the function to flash the application using bluetooth using...
Hello.
Is it possible to use multiple serial communication on 52832?
What i mean, first serial port uses for communication with custom board' micom chip.
The second...
Hi everybody,
I'm developing an product with :
NRF52840, V0.9.0, SDK15
I want to put the MCU in sleep mode (system on) and wake up with NFC or by timer (for example...
Hello,
What is the reason why my homemade PCB half passes through NRF_POWER->DCDCEN = 1; after broadcasting DCDC does not work? How do you need to solve it?
We will get a beacon from China. But how do we know if the chip is original? If I can read the unique device id, can I say it is original? Or is there another way?
I am working on the twi_sensor example,when i compiled the code it is showing as undefined symbol "data_handler(refered from main.o)", what are the changes i need to make...
Hi,
I was successfully changing mac address dinamically DURING ADVERTISING on nrf51822 chip at each ble_radio_notification event, in this way:
Before start advertising...
Hello
How do I activate Brown-out reset? I estimated there need to set some register/registers, but I cannot findout.
Possibly Brown-out reset function is always enabled...
Hello,
I work on project for BLE communication in DFU mode.
I am testing according to the mode defined on the Nordic web page link
I did the tests with the BleuZ and...
checking most of the reliable coin cell CR2032 such AS Panasonic declare on very very low current transfer far lower then 5 mA
if i set my Ble in 5mA IO OUT ....when my...
NAND or NOR flash memory to use with nrf25832? my application is to store the data from mpu-9255 to flash memory. my data rate is about 3 mega byte per hour and i have such...
Hi,
I am using Linux ubuntu 14.04 with kernel version 4.15.0-041500-generic for 6lowpan over BLE and MQTT broker wit IPv6 address as inet6 address in below image
In...
If I use DeveloperStudio_1_1_3139_0 to generate a profiles and services for the latest SDK 15.x, will it correctly work?
I recall back with SDK 11/13.xx it was not compatible...
