We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello,
Platform nRF52 with SDK 11 (S132)
I use nrf_drv_spi_init to register a Handler (used for screen and SD card so it can be long)
I have sometimes crashes when...
Hello Everyone,
I have deveoped my custom Board using(NRF51) which has four test pins VCC GND SWCLK,SWDIO. I would like to program the custom board. So could anyone tell...
I'm getting the following log messages when I try to initialize the BLE stack:
First from CHECK_RAM_START_ADDR, I get:
RAM START ADDR 0x20002080 should be adjusted to...
Hi,
I want to debug the blinky project on a nRF52 dk (PCA10040) using Eclipse. I strictly followed the instructions as described here: devzone.nordicsemi.com/.../
I...
Hi,
Is there any documentation regarding nRF OpenMesh( nRF51-ble-broadcast-mesh) Security ? Explaining the security of the communication between nodes in the Mesh network...
Hi all,
I'm working on mbed os and I cannot use the softdevice_ble_evt_handler_set and SOFTDEVICE_HANDLER_INIT . Every time I build it, I get:
undefined reference to ...
Hi ,
I am using S120 ble_app_multilink_central example. I have configured UART0 in interrupt mode. I send some command and expect some response. It work very well in starting...
Our product is based on nrf51422_CEAA chip with softdevice S110, SDK 8.0.0, dual bank ble bootloader DFU.
We have modified the dfu bootloader example from SDK 8.0.0 to...
I read a document, "Setting up production test using DTM", "nAN-034 Application Note v1.0".
And, Figure 3 shows how to setup test environment.
But, I cannot find which S...
DCDC_testing.zip
Hi,
I am in the process of reducing power consumption in micro esb mode. I use the following code, just for testing. The following code consumes 18mA unlike...
It is possible to load a new firmware in a NRF51822 PCBA using the Nordic Development Kit NRF51DK?
Do I need a special connector?
This is the beacon Module I pretend...
Hello,
I have a board with an RFDuino on it which uses a Nordic nRF51822 internally. We are seeing a few of them auto-brick when the input voltage dips too low.
My first...
I have a question about the usage of Flash Data Storage, chunks and parsing of the data retrieved from FDS.
How, when and why are you supposed to use "chunks" when setting...
Hello,
I would like to implement an interface with an external SPI ADC using the nRF52832.
The ADC has a RDY (ready) signal that goes low every time a new sample is ready...
