I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi,
Is there any chance that we can completely turn-off the radio part of nRF52832 and only the application part of the processor running. Also, we should be able to turn...
Hi,
I would like to program and debug a code into the Nordic Thingy:52. I read that I should have either J-Link or nRF52 DK. And I have the nRF52 DK, but I don't know...
Hello all,
I'm working with the nRF51 SoCs, with the s130 SoftDevice and SDK12.1.0
I have a BLE Nano from Red Bear Lab that has a nRF51822 doing adv and it expose...
I want to put application, softdevice, and bootloader into one hex file, after doing research, I think I need bootloader settings page to make the application run. I get the...
Hello,
I have been using another vendors mesh stack to develop a product that uses mesh networking, however, their stack is limited to storing provisioning data in a certain...
I'm trying to set up DFU for a custom board with a nRF52810 module (Rigado BMD-330). I created the secure bootloader from the recent project for SDK 15 posted by Vidar Berg...
Hello!
The NRF52832 uses the QFN-48 form factor but I'm having some problems finding it in Fritzing. Did some made their own, know where I can find it? Fritzing has QFN...
Hello,
I'm using SDK15.0.0, device nRF52832 and softdevice S132.
After open "secure_bootloader_ble_s132_pca10040_debug-nrf52832_xxaa_s132" project and build it, I got...
Following this tutorial : devzone.nordicsemi.com/.../
I type 'make' and it compiles for a bit and then I get a bunch of errors that say this:
[278]: *** [_build/nrf52840_xxaa...
When initializing a UART instance (0 or 1 or both together), the current consumption increases to 600 μA
Then deinitialized UART, but consumption is not reduced!
- I tried...
Hello everyone!
I've had an ESB application running o the nRF52832 for more than a year. When I moved it onto the nRF52840 it no longer works. There are no changes to the...
Hello,
I'm developing a home automation related product using mesh. For testing mesh functionality I'm placing the DK in different rooms and testing the range. As a power...
I have a small project on a custom board using an nRF51824 processor.
The code basically initializes the BLE stack timer and GPIO and then falls into a loop
while (true...
Hi everyone, There were already a few people asking about similar problem, but none of the suggested solutions worked for me so far.
I am trying to communicate nRF24L01...
