I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hello,
we have produced 10 Boards with nRF9151. Unfortunately, 3 device shows a false behavior. We cannot connect over SWD an they have a larger power consumption (whole...
I want to implement FOTA Update for a nrf5340 based board by using nrfConnect SDK v2.9.0 with zephyr and mcuboot. The board has a MX25R6435F external flash (same as the nrf5340dk...
Hello,
I am trying to run a ztest integration example I found under this one here: https://github.com/zephyrproject-rtos/zephyr/tree/main/samples/subsys/testsuite/integration...
Hi,
I am sending out same payload through ADV packet and BLE connection packet, I notice the ADV consume more power compared to connection one,which is quite strange.
...
Hi, I am using NRF connect sdk 2.6.1 and I am wondering what is the best way to run crypto operations when using TFM profile type minimal and building for nrf9160_ns. TFM_PROFILE_TYPE_NOT_SET...
I want to measure the current consumption on the DK with an Amperemeter. For that i have this setup:
Please excuse my terrible drawing skills. Im basically powering...
I am using NRF52810 as a beacon tag.
I want to apply AOA technology to this tag, is it possible?
I'm confused because the nrf52810 says it supports BLE 5.2.
Hi,
I'm experiencing memory constraints while using the nRF52811 with the SoftDevice S112, as it takes up a significant portion of the available memory. Is there a lightweight...
Hi,
We developed an application on the nRF52833 and are now porting it to the nRF54L15. As part of this process, I'm integrating an external RTC via I2C on the nRF54L15DK...
After purchasing the PPK2, I connected the Fluke287 and PPK2 Ampere meter in series to check whether the measured values matched the Fluke equipment.
The Fluke287 consistently...
Hi
I have run nrf5340 WiFi shell project in ncs2.9.0, everything ok if use Logging UART0 for cmmands(wifi scan/wifi status/ wifi connect.....etc)
now I need to use...
Hello all,
I have slightly modified the coap_client sample from the SDK such that the main function is being called on certain actions from another program. I'm getting...
I use the gpio8 interrupt to detect whether the SD card is inserted. When a falling edge is generated, it means that the SD card is inserted. But I found that sometimes, the...
So I have been doing a project on nrf52840dk, So I have built a custom bootloader for it as well, I have been trying to add the custom bootloader with the code in my nrf52840dongle...
