We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
/cfs-file/__key/support-attachments/beef5d1b77644c448dabff31668f3a47-cfe0b78c5edc467ca49b481632af4156/pair.c
I'm attempting to do LESC OOB pairing with another transfer...
Hi Team, Could you please let us know the worst case current consumption of nRF52832 at -40 and +85DegC.
Below are the current consumption values taken from datasheet: ...
Hello,
I am using sdk 12.2.2 and nrf52 customised board. Now my challenge is as follows.
When I am adding this in my code.
nrf_gpio_cfg_output(26); nrf_gpio_pin_write...
Hi all,
I use nRF52832 with the UART peripheral example.
I try to enable connection event extension in the device and get an error.
I use SDK V15.0.0 and Softdevice...
I've been trying to find a way to program a hex file onto the dongle via the command line on linux.
I would very much prefer not having to touch the mouse in order to program...
Hi, I was hoping someone could tell me if/when a version of the nRF Mesh Android App found here:
https://www.nordicsemi.com/eng/Products/Nordic-mobile-Apps/nRF-Mesh
Will...
Hi,
I'm using NRF52840 sdk v15 with Softdevice.
I have multiple SPIM instances and I make sure they are never active at the same time.
Can I share the pins (except the...
Hi, I'm trying to rate nrf52832 with stack ble_app_uart softdevice. My IDE is the IAR workbench for ARM 7.80.4. I downloaded the latest version nRF 5_SDK_15.0.0_a53641a, which...
Hi:
I would really, really, love it if you could provide a Segger SDK for Thingy! I've seen a few threads in here about the work to do it and it's a struggle. I noticed...
Hi there,
I've been searching around this forum for a while and still haven't gotten any reliable answer. I'm trying to develop a OTA firmware upgrade solution for the ATMega328p...
Hi:
when I compile project Thingy_ndoe in solution Thingy_node_s132_pca20020, an error meet,
C:\Nordic\thingy_sdk_v2.1.0\mesh_sdk\mesh\access\src\nrf_mesh_node_config...
I have combined the light switch server and client model to build control model. When i start provisioning for control model opcode status field : 2 error occurs which means...
