Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
I have a requirement where I'm using a .NET-based test adapter that communicates using the Modbus protocol over a serial (COM) port.
Now, I want to develop a BLE Central...
Hi,
so, If I take the WiFi scan sample from the nrf/samples/wifi/scan folder, and flash it to my board, I can reliably see my created hotspots, no matter if they're 2.4GHz...
I want to use gpiote and functions like:
- nrfx_gpiote_input_configure
- nrfx_gpiote_in_event_enable
This is added to the top of my document:
#include <nrfx_gpiote...
Hello,
I want to request AGNSS information from nrf cloud services using my nRF9151DK board. As a first step, I flashed the nRF Cloud multi-service application onto my DK...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hi, I am running openthread on the NRF54l15 DK. Whenever I am debugging and hit the breakpoint or pause the program, then on resumption my app crashes. How Can I debug while...
I have rebuilt the sample app at_client using VS Code (Mac) nRF Connect SDK v2.6.0 and Toolchain v2.6.0 Board target: thingy91_nrf9151 Snippets: nrf91-modem-trace-uart
I...
Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
I am using a custom board with a nrf5340 chip on it with vs code and sdk/toolchain of 2.9.1 and the bmi270 sample. I am getting and issue with my bmi270 accelerometer when...
Dear reader,
I am currently working on a project using the NRF54L15 MCU. There is plenty of documentation available for this component, and the reference circuitry for the...
Hi Nordic team,
I’m working with the nRF5340 using the Bluetooth: NUS (Nordic UART Service) example from the Zephyr SDK . Since this example primarily uses the UART peripheral...
Hello everybody,
now, I am solving problem with switching off Wi-Fi interface on nrf7002-DK. I am runnig SoftAP example on my nrf7002-DK board. So my board behaves like...
Hello,
We upgraded our project to nrf connect sdk v3.0.2 from v2.9.0 and can no longer use pin 0.00 and pin 0.01 as gpio. The problem seems to be in the nrf53 soc.c file...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...