I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
Hi,
I just received nRF52-DK recently.
I am using Ubuntu 16.04 (64-bits) OS.
I installed JLink_Linux_V620b_x86_64.deb and was using nRF5x-Command-Line-Tools_9_6_0_Linux...
Hi, I am developing an SPIS interface on the nRF51822 using SDK v12.3.
I have configured my device for EasyDMA and I expected to see a continuous stream of data being transmitted...
Hi.
I applied https://github.com/crfosse/Thingy-52-to-nRF52xx project to get thing'y motion sensor by nRF52840 DK.
When I init DK, it discovered only 7 UUID so euler,...
Hi Everyone
I am trying to use BME which is an i2c/twi sensor and EPaper which is an SPI based module. In my code i am using TWI INSTANCE ID 0 AND SPI INSTANCE ID 0.
I...
Hi all:
I am developing the driver of ST LIS3DH and its mcu is NRF52.
If I want to read the value of whoami.
I am not sure if I need call the function of
nrf_drv_twi_tx...
Hi everyone. I'm starting from scratch and using as reference the example/ble_peripheral/ble_app_template.
I'm using Embedded Studio 3.50 + Jlink V6.32 / The chip is nRF52832...
Hi,
I am running the BLE app uart example, using Segger Embedded Studio in Windows.
I've found that that after build and run procedure, the firmware doesn't run, as there...
I am using Master Control Panel 3.10.0.14 with 2 nRF51 Dongles. I can select a dongle and perform a Start Discovery and see devices. Next, I install Microsoft Universal Windows...
Hi
I'm facing a problem since I've upgraded to SD140 6.1 .
I'm running as multilink central, and want to keep scanning even after connection. I scan with the following...
Hi,
I am working on an application using the nrf52 sdk v15 and nrf Mesh sdk v2.1.1 on nrf52840 PDK. Starting from the nrf5_SDK_for_Mesh_v2.1.1_src\examples\sdk_coexist\ble_app_uart_coexist...
I'm currently adding a large characteristic (5.3 times bigger than my max MTU) to my device that supports multiple peripheral connections. This characteristic is used to set...
Hi.
I want to get thingy's sensor data on nRF52840.
I found that 'ble_app_multi_link_multi_role' example, but there are only get button and led state.
By using that...
