I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Its the first time I use simple_timer. I do not use the Softdevice. So I'm working with the peripeheral simple_timer example(SDK11).
I know from the app_timer, that every...
Hei!
I recently added WDT to my existing project. After that the normal behavior/sequence of code is not as it is supposed to. Strangely it works okay every other run now...
I just get DK P10040, I am using SDK_11.0.0_89a8197/s132_nrf52_2.0.1_softdevice.
I tried ble_app_uart, it works.
But I find a problem, I cannot set P0.09/10/12/13 high or...
I'm trying to compile nRF51 SDK 8.0.0 under Windows.
So for that purpose I'm going to components/toolchain/gcc and running 'make' there.
No targets specified and no makefile...
Hello,
I find in your source code contradictory values for the UART TX and RX characteristics.
E.g. have a look at nRF toolbox (both Android and IOS) definitions: github...
Hi all,
I am trying to implement DFU on my device with marginal success. Here are the steps that cause the issue:
Using nRFgo Studio: "Erase all", "Program Softdevice...
hi
I use S130 from nRF5_SDK_11.0.0_89a8197 as an ble central base on ble_app_uart_c example. when the ble_peripheral change the adv's content(means have data to send),the...
I have been able to follow the instructions in the nrf5 iot sdk to connect my nrf52 dk to a raspberry pi, however I am unsure why a connection must first be made before I...
Hi,
I'm using nrf52 with S132. I noticed high current draw after calling sd_ecb_block_encrypt() function.
After calling function consumption is 6mA and stays at a constant...
Hi,
I would like to read and update value of the characteristic received from AD pin AIN0. I already tested the following code, where I got very weird results (value is...
I am using Keil MDK v5.2 to compile ble_app_uart example using the project in examples\ble_peripheral\ble_app_uart\pca10028\s130\arm5_no_packs
I am using the latest nRF5_SDK_11...
I would like to use the capsense example with a Bluetooth application. But as it's not compatible with softdevice, I want to modify it. Two questions:
1 – As anyone already...
HI,
I have very basic question: I plan to connect two devices on i2c to the nrf52. Can they both be connected to the same pins, and configured by software to select one...
I have been analyzing the Bluetooth snoop file on several Android devices, where the Android device is the Central (Client) and the peer device (nRF51822 with S130) is the...
