When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
sometimes it discovery service no matter ,sometimes it stuck when call sd_ble_gattc_primary_services_discover and no callback event 。 why it is ？ is a bug ?
HI,
Under nRF5_SDK_12.2.0_f012efa, with s132_nrf52_3.0.0_softdevice, run on system on low power mode.
I define an app_timer,below is my parameter
APP_TIMER_DEF(m_second_id...
Dear Nordic community
(SDK v14.2, nRF52832)
I have a real-time application where I am sending 6 packet of 20 byte Notification per connection interval. And there is not...
Hi,
When debugging with sdk_15.0.0 ble_app_butonless_dfu project(application project) + secure bootloader project(bootloader project),it will cost about 2~3 minutes for...
Hi,
I am trying to modify the multilink central example to send string to other board.
In the main.c I inserted the uart_init(), uart_event_handle() methods
I added...
Hi everybody,
I'm developing an product with :
NRF52840, V0.9.0, SDK15
In the DK I connected LIS3DH (accelerometer by TWI)
all works.I configuration of HZ and temperature...
Dear Nordic team,
I want to add DFU services to an existing application which is based on ble_app_uart example.( SDK 15.0.0, softdevice S132 6.0.0)
What I have done is...
Im working on merging blinky_c with light_switch_server. Took the blinky example as starting point then merge the mesh code accorging the Coexistence with nRF5 SDK BLE functionality...
The issue is that I fixed some of your bugs in the attached file, as follows:
Changed to handle larger number of records greater than 256 records, we need 500 records...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
hello
Im trying to send a small array with two integers over bluetooth mesh
but Im getting error code 7 invalid params..
how should I send an array like this?...
Hi,
I am working on PB Remote example. I would like to be able to run remote scan on my 5 servers immediately after they are provisioned.
For example, I provision the...
I have been using nRF Connect on a Samsung phone for a couple of months, and have forgotten how to install it. My daughter was playing with the phone and managed a factory...
I'm working on a BLE design for nRF52832, with SoftDevice S132 v5.0.0. The project uses FreeRTOS with Tickless Idle enabled. When the user powers the device off (from a UI...
Good morning,
I've inherited a line of nRF51822-powered products that are currently running firmware based on SDK10 and SD130 v1.0.0. UICR-> BOOTLOADERADDR is set to 0x3b000...
