Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
To the kind attention of Nordic support team,
In PCA10059 hardware files C10, C13 and C25 are not conected when I see in the bill of material. But it seems that in the real...
Hi,
I am currently just trying to clone the nRF connect sdk according to the getting started assistent.
All the first steps just worked fine, but I ran into a problem...
Dears?
When I click the download link of nRF Sniffer v2.x ,it show "page not found(Error404)"
Would you help me?
nRF Sniffer User Guide v2.2 is to be used with the...
Hi Sir,
In normal, we can see three virtual COM ports in nRF connect - programmer, first is for nRF9160, second is for nRF52840, the last is for nRF9160 but not use.
Then...
Hi
I have a wired situation in my project. Everything is working fine when I am running my heart-rate device with the debugger. When I detach the debugger or just power...
Hello
A project that recently made a sensor found that the timer consumes a lot of power.
I built a timer to collect sensor data in the timer handler.
Sensor only...
Platform NRF52832 SoftDevice S132 V6.1 SDK 15.0 FreeRTOS implemented
Hi, In our application, once the mobile app is connected to the peripheral, it makes continuous writes...
Hi, I've started an 802.15.4 project using the nRF52811 and see that support in the vSDK 15.3.0 explicitly states the 802.15.4 stack is only for another part. Is there support...
What is the manufacturer and part no. for the nRF52840 DK's NFC Antenna?
I have lost mine and would like to purchase a replacement. I have seen this previous discussion...
Hi,
I have my project working using the nRF52 development board.
A BMP280 pressure sensor is connected TWI to the board and pressure measurements are sent over bluetooth...
Hello everyone,
I trying to communicate nrf52832 SDK 15.0 ble_app_uart(peripheral) to ble_app_uart_c (central) with secured purpose adding static passkey but i don't get...
Hi,
Since migrating to SES 4.18 erasing of the flash hangs unless the JLink is unplugged and plugged in again. This is both on the DK and our own custom board. Here's the...
I looked at the info center for the part as well as the 3rd party modules; but couldn't find an FCC ID.
Does this chip (or possibly an equivalent part) have an FCC ID?
Hey All,
I'm building firmware for a central, that I want to have the ability to switch between scanning for a complete local name, or if none is given, scanning by way...
