I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
Hi all. I want to measure current consumption on nRF52840 DK (PCA10056).
I have the SB40 cut and the 12 Ohm resistor placed in R90. I measure the voltage on this resistor...
Dear team：
How can I use ble-bas-c to change Characteristic UUID or Connect the 1800 service and rename it with the 2A00 feature value The example is \SDK\nRF5_SDK_15.3...
Hi,
I am new to this. I want to build a mesh network using nrf52832. I have already downloaded and gone through nrf5 SDK for mesh but i am confused about what to use to...
I am using nrf51822 DK. How to set GPIO pins as output pins and access the pins to set or reset the output.For example if I want to use pin 20 as output, how to configure...
I am trying to read if an input is 0 or 1 but for some reason it takes the first one its offered and then it does not change anymore.
int main(void)
{
nrf_gpio_cfg_output...
<Environment> - nRF9160 DK v0.8.5 - nrf tag: 1.1.0 - modem version: 1.1.0 - using an external GPS antenna, SW12 => CON
I'm attempting to use udp_gps, but doesn't work out...
Hi all,
I'm a bit confused. After going through available documentation, I thought I had understood that RTC0 was used by the SoftDevice, but that RTC1 was available to...
Hi,
I am using nRFmesh SDK for a project. I have configured all nodes(devices) into one group. Each device will publish message for every three seconds. I am reading the...
Hi,
I need step by step guidance on how to implement BLE MESH ( SIG MESH) using nRF52840 Dongles.
I am trying to connect 5 dongles in MESH config.
Kindly help with...
Hello. I am using nRF52832. The SDK version is 14.0.0. UARTE is used for serial communication with other devices. The baud rate is 38400bps, and a maximum of 20 bytes of data...
Hi, I could not find a way to use Segger Studio debugging features when I have a bootloader for DFU functionality. Is there a way to something like that, because when I click...
I am trying to read temperature, pressure, and humidity data from an Adafruit BME280 sensor using the nRF9160 DK. The communication protocol that I am using is I2C and I am...
Hi,
In our product, we use 9160 GPIO to control the system power. However, we found we can't power off when 9160's modem is in normal mode. But, the system can power off...
