I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
Can any one Explain me the Following Error
GATT INVALID OFFSET in the Clinet(nrf master control panel APP)
I am getting this error when i try to send more than 23...
Hi,
we are designing a module with the nRF52832 WLCSP. As the module will be soldered on a motherboard a second soldering process respectively a thermal exposure will take...
I would like to load the blinky example on the nRF52 preview development kit. When I try to build the project I will get this error:
Error #541: 'ARM::CMSIS:CORE:3.40.0...
Hello, this question is similar to this questions (Scan request packet, answered by John DeWitt and Aryan)
I'm using
IAR EWARM 7.20
PCA10001 V 2.0.0 ...
We are using nrf51822 AB variant(16kb Ram, 128 kb flash). Due to flash size constraints we are still using s110 softdevice v5. Following is the linker script config:
FLASH...
Hi,
I have setup my system for working with nrf51822 with openOCD and STLink to program it. The blinky went well. But now when i try to program it i get the following error...
I have just concluded a three year development using TI's Tiva ARM M4 chips, writing both bootloaders and applications.
I am using an RFduino to explore BLE.
I have...
Hi all!
Today I run tests in a public place (some Art Design College) and it looks that radio environment, that exists in the place, kills nrf51 completely....
My guess...
Hello.
I want to flash DFU bootloader with keil on chip nRF51822-CEAA (256kB flash, 16kB RAM). I'm using s130
The areas i write to are:
IROM start: 0x3C000
IROM...
I was wondering if it would be possible to add an event for Service Discovery (and other similar BLE stack events) that could be detected by user applications. Per answers...
hello there i have two nrf51 dk kits. now i want that one act as central and other act as server.
i want to communicate between two. can you tell me how to do it??
i think...
hello all:
IN s310 multiprotocol--ble_ant_app_hrm example ,I open the macro BONDING_ENABLE, then i compile,there is a error
......\main.c(674): error: #136: struct ""...
