It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
Background
For reasons that I do not want to dispute here, I am building a custom bootloader for the APP + NET cores on the nRF5340. This custom bootloader is not a Zephyr...
I am testing out the nRF54H20 on the nRF54H20-DK version 0.9.1. I have followed the steps for setup in the "Getting started with the nRF54H20 DK". I currently have nrf54h20_soc_binaries_v0...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I'm trying to run the DFU sample l9_e5_sol on a custom board using the nRF5340 and SDK version 3.0.2.
My goal is to perform DFU over BLE using external flash. However, before...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
hi
im use nrf52840 as a gazell device which run the demo \nRF5_SDK_16.0.0_98a08e2\examples\proprietary_rf\gzll\gzp_desktop_emulator\pca10056 ,and use nrf24lu1p
(\nrfready_desktop_2_v3...
I am porting a peripheral project from nRF51822 on SDK 11 to nRF52832 on SDK 15. Currently I'm using15.0, with S132 6.0.0. I used the template project for an initial pattern...
Haii i'm using Nordic nrf52840 with SDK 15.0.0 and soft device of s140
now my issues is i want to connect a four device to the central and there should be Bidirectional...
To establish a connection to a nRF51 Dongle I have recently following problem:
A J-Link Window “J-Link Window_Device Selection.png” appears and in the following Window ...
Hello everyone,
I'm developing a custom software with SDK 15.3, SD 132 6.1.1 following the ble_app_hrs example for supporting Peer_Manager and Encrypted Link.
This is...
Hello!
I am trying to get the old window application for the Power Profiler Kit v1.1 at https://www.nordicsemi.com/Products/Power-Profiler-Kit but the page is not available...
SDK Version : Mesh 4.0 & SDK_16.0 Software : Segger Embedded Studio
Hardware : 2 PCA10040 devices as a client and a server
System : Windows 7 Hi,
I want to send a string...
I am starting to get up to speed on nrf_crypto, but trying to understand under what scenarios would one choose between Oberon or micro-ECC backend ?
HW = nRF52832, SDK 16...
Hi all,
I am testing the OpenThread connection with 3 nodes at the present,
One is working as End-device with MTD (Minimal Thread Device) firmware others are FTD (Full...
Hi Support Team,
In reading this white paper,Section 3.5 Testing RF performance,
a colleague informed me that a test UICC which is provided by the LTE tester vendor say...
Hi All,
I'm using hci interface to scan the ble based beacons.
While scanning hci interface's Rx bytes keep on increasing because beacons are being scanned.
I'm using...
Dear everyone,
My platform is SDK16 and IDE is KEIL V5.25.
I set timer 2 to 104uS to sample a serial data. It isn't UART data, no start bit and stop bit.The start bytes...