Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
Hello,
I tried to mix AWS_FOTA sample with GPS from asset_tracker (see code first screenshoot) and I get that error (see second screenshoot). Do someone have an idea please...
Hi,
I am using nRF52840 DK with USB and BLE prototype under hardware peripherals example in the SDK. I need a real world example using BLE with USB as host interface. Can...
nRF52840 works with 1.8V supply voltage? We are using Circuit configuration number.5. it tells VDD should connect to VDDH.
As per the circuit configuration 5: VDDH is N...
Hi :
we met some quesiton when using nRF52840:
1. Is it possible to drive a pin to high or low in sleep mode? For eg. we would like to put pin P0.12(may be other pins...
I am trying to communicate between an ADXL362 accelerometer and a nRF9160 DK. I see on this link https://docs.zephyrproject.org/latest/samples/sensor/adxl362/README.html that...
Hello
we had purchased nRF6700 and nRF24LE1-F16Q24-DK from Mouser India on 14-oct-19 .and it comes with an older version of firmware i.e.(3743) And currently, I am facing...
Hello:
I have to nRF52DK boards and I am able to run the ligth_switch example, but the thing that I want to do is send a message, "hello" from one node to other. I saw...
Sir in the above code i have a cmd_zb_match_desc() but i am calling inside the switch case but after calling i didn't able going inside the finction
please give the Suggestion...
HI,
I want to send heart rate data to smartphone using NRF51422 in every second without any time delay or minimal time delay ranges between(0.9 to 1.1 sec).
Thanks...
Hello,
I managed to get a central application to run on the nRF52810 with SDK 14.2 and S132 V5.1.0. I also got the bootloader working with this setup.
Right now I'm having...
Hi!
I have nrf52 periperial mode, SDK15, s132.
I connect a smartphon in the central mode to my nRF52 and start to send some data.
In the nRF52 I receive those data in...
Hi, I am trying to print double/float values, but Its printing blank. e.g. printk(" value:%.3f\n", value); output: value:%.3f printk(" value:%lf\n", value); output: value...
My project consists of reading an NFC card's value (using another chip), and respond to the interrupt generated by that chip to read the value from it using SPI. Then, this...
Currently I am using VS Code for development. Mostly everything is fine and VS code is awesome.
However there are some problems I am facing.
1. It is time consuming to...
