Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
I am trying to communicate between an ADXL362 accelerometer and a nRF9160 DK. I see on this link https://docs.zephyrproject.org/latest/samples/sensor/adxl362/README.html that...
Hello
we had purchased nRF6700 and nRF24LE1-F16Q24-DK from Mouser India on 14-oct-19 .and it comes with an older version of firmware i.e.(3743) And currently, I am facing...
Hello:
I have to nRF52DK boards and I am able to run the ligth_switch example, but the thing that I want to do is send a message, "hello" from one node to other. I saw...
Sir in the above code i have a cmd_zb_match_desc() but i am calling inside the switch case but after calling i didn't able going inside the finction
please give the Suggestion...
HI,
I want to send heart rate data to smartphone using NRF51422 in every second without any time delay or minimal time delay ranges between(0.9 to 1.1 sec).
Thanks...
Hello,
I managed to get a central application to run on the nRF52810 with SDK 14.2 and S132 V5.1.0. I also got the bootloader working with this setup.
Right now I'm having...
Hi!
I have nrf52 periperial mode, SDK15, s132.
I connect a smartphon in the central mode to my nRF52 and start to send some data.
In the nRF52 I receive those data in...
Hi, I am trying to print double/float values, but Its printing blank. e.g. printk(" value:%.3f\n", value); output: value:%.3f printk(" value:%lf\n", value); output: value...
My project consists of reading an NFC card's value (using another chip), and respond to the interrupt generated by that chip to read the value from it using SPI. Then, this...
Currently I am using VS Code for development. Mostly everything is fine and VS code is awesome.
However there are some problems I am facing.
1. It is time consuming to...
Hi,
In my application,for the first time device (nrf52832)will start advertising and on nrfconnect for mobile application side we make it get connected and bonded.It may...
Hello! I'm trying to develop an Android-nRF-Toolbox App. What features and folders do i use with show logs? In order to develop the uart in the toolbox app, we have deleted...
Hi everyone,
I want to know that is it possible to send the heart rate data using HRM services without sending the battery data in nRF51422. When I disable the battery...
Hi! I've been working with the Thingy 91 and I've found that the SIM card was running out of data, so we decided to buy more data to keep working. The board was working as...
