Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi I wanted to ask if there is a driver/library for the mcp25625 chip? Also for the communication do I use " SPIM — Serial peripheral interface master with EasyDMA " or "...
I'am achieving lowest power consumption in connected mode. I can't identify source of short spikes every 40Hz when mcu is in low power mode. I'am sure that it's not application...
under code is my sdk main code and i want to change code to Sensor --I2C-- nRF52 --UART-- app but where i have to start and change ?
/* Copyright (c) 2010 - 2017, Nordic...
I've been doing some testing with Mesh DFU and I've noticed some unexpected behavior around handling missing data segments.
As I understand the Mesh DFU protocol, if a data...
I have issue about calibartion using saadc.
I use 52832, S332, SDK 15.3.0
when calibration is excuting, ANT+ and BLE is also doing.
I use low power mode in saadc.
...
Hi
I want to know if there is any source code of thingy91.
Because I want to follow thingy91 for making a product with the use of the same antenna, and I want to know...
Hi,
Recently, I was trying to move my project from STM to Nordic IC.
I just wonder how to implement the below codes into the nRF52832 or how to program it in Nordic environment...
Hi,
I want to set sending power(+4dBm) of NRF52810/NRF52832 with SDK 15.0.
Now,i find i should use the order of sd_ble_gap_tx_power_set(uint8_t role, uint16_t handle,...
Using a AF_INET UDP socket on the nrf9160 I will get ENOMEM when I send a bunch of datagrams over the socket. I understand how there can be a limited number of buffers for...
I am trying to debug the dfu bootloader using SES. This is my first time using SES. I opened the example project and everything builds fine. The image loads on the device...
I am currently working on a design with the nRF9160, and have a few questions about the DEC0 pin and decoupling for the module in general. I have been considering adding additional...
Hello,
I am use bonding and want to forbid new bonding if proprietary authentication criteria is not met.
For example, I want to allow bonding only if my device is on...
Hi, I am using nRF5_SDK_15.0.0_a53641a.
I'm using code below to start WD and I'm not feeding WD.
After WD reset, I'm looking at RESETREAS register and DOG bit is...
Hi,
we are currently in the process of optimizing our connections for better throughput. Use-case is connection based FruityMesh ( https://github.com/mwaylabs/fruitymesh...
Sir i am using only one nrf52840 board
Sir i am changing router role to coordinator role and also remove the zb_ed_role in preprocessor definition
now the project building...
