Hey there!
I am facing a very frustrating issue, where my nRF54L15 (custom board) BLE peripheral just won't appear in mobile apps.
For example, right now I am trying to...
Hi all,
I'm deploying an nRF9160-based device in India and hitting the familiar "which SIM actually works here" wall. Looking for current (2026) experiences, since older...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
Hello,
I am working with the nRF52 DK and the PPK (Power Profiler Kit), however I can only program the DK when the PPK is connected. Once I disconnect the PPK the message...
Hi,
We are developing weareble with nrf52832 and already made 6 test modules. Everythink works fine except 1 module. This wonderful piece is visible only on PC Win 10 ...
Hi,
I am designing a BLE Device based on nRF51822, which broadcast three services : one home made service, the Battery Service, and the DFU service for the OTA update....
Hi guys,
Currently, I used JLink V8 to program, load code to nRF52823.
I connected this JLink to nRf51822, then it works perfectly but when come to nRF52823, it doesnt work...
Hi,
I am working on nRF52832 with SDK13.0 + GCC Eclipse.
I have used 2 app_pwm instances for driving a 3 color led. Once I init the pwm and set the duty cycle, the current...
Hello, do I do it in some sort of system initialization function? That would be really strange because that's not the case with example projects, or do I do it using nrfjprog...
I am using PCA10028. I am not able to verify the output for given examples of SDK 12.2.0 that require master emulator or UART.
I have the pin 0.30 connected to ground as...
nRFready Smart Remote 3 nRF52 v1.1(PCA63519)
SDK: nRF5x SDK v12.2.0
IDE:Keil 5
Hi,I am trying to flash the whole package of SR3.
1.Flash the s132_nrf52_3.0.0_softdevice...
I'm changing the DEVICE_NAME macro in the example and then flashing but for some reason when I scan for available Bluetooth devices, the device always turns up as Nordic_UART...
Hi All,
Can one safely assume when sending a packet to a destination address using the ping command in the CLI, that the payload echoed back is the payload transmitted...
mainc.txt
we can use INTENSET to enable certain events on the radio as in line 460 in mainc file attached. But how to enable this on the radio as a whole.
I basically...
Hi Nordic,
I am trying to enable the DC/DC converter on a QFAAH10 (revision 3) .
I am using the s130 v2.0.1 SD .
----------
1. sd_power_dcdc_mode_set(NRF_POWER_DCDC_ENABLE...
Hi,
If I configure the radio notification to ACTIVE and then set a DISTANCE of 800us, is there any way that I can configure PPI to toggle a pin for example?
I know that...
We are applying the CE certifcate for a product using nRF51822 and softdevice S130. Certification lab requires us to fill in below techanical questions. Please help to answer...
Hello, my program stuck at these assembly codes:
I decided that it was stuck because I keep pressing F11 and it just go around in circles in these 4 lines.
So:
...
