nRF NCS 3.0.x
Target : nrf5340dk or native_sim
What is the latest recommendation on build environment (assuming preference is a docker image for consistency of build...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Are there any migration guides for a customer who wants to migrate from nRF5340 to nRF54L15? And if they are nRF54L15 in chipscale, anything they should be aware of including...
We need to sense temperatures in the upper end of the operating range, specifically in the 40C to 70C realm. We have three different units, and we are finding that the temp...
Hi,
We're evaluating NFC for our project.
I've been testing with a nRF52840DK - PCA10056 Version 3.0.2.
Using the antenna supplied with the Development Kit I am...
Hi,
I have been playing around with the configs but I could not get Mode-3 to activate. What should I change for cs configs and the prj.conf file in order to activate it...
Hello - We're designing a new app for our product in Flutter. I was writing the proof of concept for the firmware updates, but I hit a roadblock with a Mcu Mgr Error: 25 ...
I was under the impression that HomeKit was an extension of the MFi Accessory Interface Specification, which relies on the iAP protocol to access additional functionality...
Hi.
We are developing a test equipment for devices that use nRF905. The devices use single ended connection for 50 Ohms antenna and layout recommended by datasheet (nRF905...
Hi,
I am using ios app to connect nordic BLE module. I am getting continuous disconnection after 1 minute on app . Please let me know how to configure for continuous data...
HI:
I use my own nRF51822 board for a snifer(not PCA10000, PCA10001 and nrf51822 development dongle). Run ble-snifer-.exe, I could ger the information as figure 4 in ble...
currently i am using nrf52 as spi master with an imu as spi slave. based on the sdk code spi_master_with_slave, I write a sample test code to read the register value from...
Hello Nordic Community,,
Do I need the typical MBED hardware setup (Interface chip connected to 'target' (the nrf52)) in order to program the nrf52 with FOTA using an MBED...
Hi,
I'm using nrf51822. After sending a data from TXD, I enable the TXDRDY interrupt by setting INTENSET register. Then I can get into TXDRDY interrupt handler function....
Hello,
I found some posts discussed before.
I2C/TWI slave with nRF51822 [closed]
Using NRF51X22 as TWI Slave
In SD8.0, SDK10, does it still only support the TWI...
Is it possible to somehow get access to the channel hopping data from BLE. We're trying to trace some interference from an external device, and want to be able to see when...
Hello,
How to put values changing over time into advertising data?
What I want to acchieve is to send ADC values that are changing dynamically over advertising packet...
We're designing a new revision of our open source sensor beacon platform: http://ruuvi.com
Just want to make sure I got this right. nRF51/2 Reference PCB Guidelines states...
Yeah. It's that topic again.
I tried to measure the current with an oscilloscope (Agilent 100Mhz; 2GSa/s).. but that didn't quite work.
Can you maybe share how you guys...
Hi
I have tried to convert ble_app_uart to use spi slave rather than the uart with no success.
Please can I have some pointers as how to go about it.
Thank you
Hi,
system info:
SDK: v6.0.0.43681
S110 V7.0.0
nRF51822 Rev.2
I’m using a ~4ms one shot timer (using the timer library) which is being started in the...
